User's Manual

USER MANUAL
Version：1.1
Neutral-free WiFi dimmer switch-TERMINALS: D2L04W- S/S3/SA/SA3/P/P3/
PA/PA3/PB/PB3/PC/PC3
Neutral-free WiFi dimmer switch-WIRES: D2L04W-SW/SW3/SWA/SWA3/PW/
PW3/PAW/PAW3/PBW/PBW3/PCW/PCW3
Neutral-free Digital dimmer switch-TERMINALS: D2L04-S/S3/SA/SA3/ /P3/PA/PA3/
PB/PB3/PC/PC3
Neutral-free Digital dimmer switch-WIRES: D2L04-SW/SW3/ WA/SWA3/PW/PW3/
PAW/PAW3/PBW/PBW3/PCW/PCW3
Please read carefully this manual before installing and using the product.
PICTURES ONLY
FOR REFERENCE.
PRODUCT SPECIFICATIOIN
D2L04/W-S/S3/SA/SA3
/SW/SW3/ SWA/SWA3
® COPYRITHT DESERVED BY SZ TSYL GENERAL TECHNOLOGY
RATE INPUT
120V~ 60Hz
WIRING
TERMIANLS or WIRES (Please refer to wiring diagram)
LOAD
MINIMUM: 7W; MAXIMUM: 150W(LED) 350W(INCANDESCENT)
LOAD TYPE
LEDs (Dimmable), INCANDESCENT,HALOGEN
DIMMING RANGE
MAXIMUM RANGE 3~95% (Depends on load,)
DIMMING MODE
LEADING EDGE, Only for dimmer switch
COMMUNICATIN
WiFi 802.11.b 2.4G
ENVIRONMENT
-5ºC~40ºC；5%~95% RH, NON-CONDENSING
STANDARD
UL 1472
Know your switch/dimmer switch:
Thanks to the revolutionary IOT technologies from SZ-TSYL, D2L04/D2L04W series
dimmer operates 2 wires mode without neutral. It is easy to upgrade your lights to smart
lighting without re-wiring.
The WiFi modules are built-in for the models D2L04W. It accesses the internet by router
directly without an IoT gateway. It allows users to save costs on smart homes. It is
controlled by Apps, and the third smart speaker such as Amazon’s Alexa, Google Assistant.
PRODUCT INTRODUCTION IN BRIEF:
SWITCH
Push ONE time the push-button to TURN ON or TURN OFF.
Tips: Push and holding or pushing the button quickly will trigger other functions.
DIM
Way-1: Push and hold the push button to dim up/down circularly
Way-2: Slide the Slide-toggle to a particular position to set the lighting level (Only
model D2L04-S, D2L04W-S)
Way-3: Dimming or setting the lighting level by Apps or by AI speaker
( Amazon’s Alexa, Google Assistant, Only model D2L04W series);
Tips: Push quickly will trigger other function.
SETUP
Light-level setup: Click the push-button quickly 5 times to start the light-level setup
mode, dim a minimum lighting level what you want, then click quickly 2 times
(double click), the dimmer switch will set up the present level as Min light-level. In
the light-level setup mode, dim a Maximum lighting level what you want, then click
quickly for 4 times, the dimmer switch will set up the present level as Max light-level
Reset to factory setting: Push the push button quickly for 9 times
FUNCTIONS
LEDs
OPERATING
REMARK and TIPS
Reset to Factory
Blue LEDs flash for 30s
Click the button for 9 times
Click for ONE time is less 0.5s,
Light-level setup
Blue and Orange LEDs flash
alternatively
Click the button for 5 times
It will turn back in 30s.
Click for ONE time is less 0.5s.
Turn on/ Turn Off
Blue= Turn ON;
Orange=Turn OFF
Click the button for 1 time
Push time is in 0.3¬1S.
Dimming-
Manually
Orange and Blue blending to
indicator the lighting level
Push and hold the button
until got your intended light-
level; Or slide the toggle
You can set the max and min light
level of your dimmer according to
your lamp and habit.
Online Setup and
Dimming
Please refer to above
Operates by Apps and Smart
speaker
Please refer to guide on Apps and
Smart speakers
Push
button
LED
Indicator
Toggle
Hard
Switch
Light level LEDs
status LEDs
Up button
Down button
Hard Switch
Push
button
LED
Indicator
Hard
Switch
D2L04/W-P-/3/A/A3/W/W3/AW/AW3
AP10W-P/P3/A/A3/PW/PW3/AW/AW3
D2L04/W-P-B/B3/C/C3
/BW/BW3/ CW/CW3
FCC CAUTION:
Any Changes or modifications not expressly approved by the party responsible for compliance
could void the user's authority to operate the equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
IMPORTANT NOTE:
Note: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:—Reorient or relocate the receiving antenna. —
Increase the separation between the equipment and receiver. —Connect the equipment into
an outlet on a circuit different from that to which the receiver is connected. —Consult the
dealer or an experienced radio/TV technician for help.
Doesn't work and LEDs never light: Check the if the dimmer switch is installed correctly, check the
Hard switch or the dimmer is pushed down, check the breaker is turned on, check if the lamp is
OK and installed correctly;
Lamp/bulbs flicker: Check the lamp/bulbs are dimmable and power more than 7W;
Lamp flicker at the minimum/maximum level: Set an appropriate minimum/maximum light level.
Limited diming range: Check the setup maximum and minimum light level. Reset to factory set up
by pushing the button 9 times.
Can't connect to WiFi network: Check if your operating follows up on the guide. Check if there is a
WiFi network. Check the WiFi router is compliance with 802.11 b/g/n.
TROUBLE SHOOTING