Product Manual
Date Printed: 6/19/2018
764-2056
INSTALLATION INSTRUCTIONS
WATER SEPARATOR MAINTENANCE
1. Release system pressure.
2. Remove tube from filter head by holding filter head and rotating tube
counter-clockwise.
3. Using a 5/16” or 3/8” wrench, remove baffle from threaded rod below
element.
4. Remove bottom baffle, filter element, top adaptor (120 & 240 Series
Filters Only), and O-ring.
5. Clean stainless steel mesh with soapy water or replace entire
element with service kit. Refer to Service Chart shown above.
6. Replace filter element and hardware in reverse order from previous
steps. Tighten baffle until filter element can no longer spin freely. DO
NOT OVER TIGHTEN!
7. Reinstall outer tube by rotating clockwise onto filter head.
8. Slowly pressurize the unit.
Figure #1: Water Separator Figure #2: Oil Coalescing Filter Figure #3: Acvated Carbon
WARNING
Your safety is important. System pressure must be released prior to any installation or service. Failure to follow instructions could result in operating
failure or product damage. Always install filtration with the arrows indicating the direction of airflow. Use only appropriate thread sealant on all connection
fittings unless otherwise specified. Do not alter the filtration from its original design as this may cause failure in its operation parameters.
OIL COALESCER / ACTIVATED CARBON MAINTENANCE
1. Release system pressure.
2. Remove tube from filter head by holding filter head and rotating tube
counter-clockwise.
3. Using a 5/16” or 3/8” wrench, remove baffle from threaded rod below
element.
4. Remove bottom baffle, filter element (element gaskets, 20 Series
only), top adaptor, and O-ring.
5. Replace filter element and hardware in reverse order from previous
steps. Tighten baffle until filter element can no longer spin freely. DO
NOT OVER TIGHTEN!
6. Reinstall outer tube by rotating clockwise onto filter head.
7. Slowly pressurize the unit.
DRAIN REPLACEMENT INSTRUCTIONS
Float Drain
1. Release system pressure.
2. Remove bottom cap by holding filter tube and rotating bottom cap
counter-clockwise.
3. Grasp float drain by stem and rotate counter-clockwise.
4. Reinstall new float drain by spinning in clockwise direction until O-
ring contacts the end cap. Tighten an additional 1/4 turn. DO NOT
OVER TIGHTEN!
5. Reinstall end cap on filter tube.
6. Slowly pressurize system.
Pneumatic Drain
1. Release system pressure.
2. Disconnect pilot line tubing.
3. Remove pneumatic drain by holding filter tube and rotating
pneumatic drain counter-clockwise.
4. Reinstall new drain by spinning in clockwise direction. DO NOT
OVERTIGHTEN!
5. Reconnect pilot line tubing.
6. Slowly pressurize system.
Electronic Drain
1. Release system pressure.
2. Drain from power source.
3. Remove electronic drain by holding filter end cap and rotating
counter-clockwise.
4. Reinstall new drain by spinning in clockwise direction. DO NOT
OVERTIGHTEN!
5. Reconnect to power source.
6. Slowly pressurize system.
Water
Separator
Service Kit
Oil Coalescing
Filter
Service Kit
(5 Pack)
Coalescing
Elements
Activated
Carbon Kit
(5 Pack)
Activated Carbon
Elements
(3 Pack)
Float
Drain
Pneumatic
Drain
Electronic
Drain
20 Series
21999-0846 21999-0394 21999-0823 21999-0395 21999-0824 21999-0868 21999-0792 21999-0177
50 Series
21999-0227 21999-0202 21999-0825 21999-0200 21999-0826 21999-0868 21999-0795 21999-0177
120 Series
21999-0228 21999-0202 21999-0825 - - 21999-0868 21999-0805 21999-0177
240 Series
21999-0228 (x2) 21999-0202 (x2) 21999-0825 (x2) - - 21999-0868 21999-0805 (x2) 21999-0177 (x2)
800 Series
21999-1005 - - - - 21999-0868 152-0000 21999-0177
Service Part Number Guide
*Bae sizes may vary
based on lter model