SMART ELLIPTICAL MACHINE SF-E3889 SMART USER MANUAL IMPORTANT! Please retain owner’s manual for maintenance and adjustment instructions. Your satisfaction is very important to us, PLEASE DO NOT RETURN UNTIL YOU HAVE CONTACTED US: support@sunnyhealthfitness.com or 1-877-90SUNNY (877-907-8669).
IMPORTANT SAFETY INFORMATION We thank you for choosing our product. To ensure your safety and health, please use this equipment correctly. It is important to read this entire manual before assembling and using the equipment. Safe and effective use can only be achieved if the equipment is assembled, maintained and used properly. It is your responsibility to ensure that all users of the equipment are informed of all warnings and precautions. 1.
PRE-ASSEMBLY CHECK LIST Before you start to assemble, please make sure all parts are included.
No. Description Spec. Qty. No. Description Cover for Left Swing Bar Spec. Qty. 1 Main Frame 1 51L/R 2 Handlebar Post 1 52 3 Rail Frame 1 54L/R 4 Front Stabilizer 1 55 Nut Cap 1 PR. 68 Meter 1 1 71 Adaptor 1 5L/R 6 Swing Bar Fixed Handlebar 1 PR. Roller Cover 2 Pedal Cover for Right Swing Bar 1 PR. S13 2 9L/R Pedal Arm 1 PR. 78L/R 1 PR. 11L/R Handlebar 1 PR.
ASSEMBLY INSTRUCTION We value your experience using Sunny Health and Fitness products. For assistance with parts or troubleshooting, please contact us at support@sunnyhealthfitness.com or 1-877-90SUNNY (877-907-8669). STEP 1: Remove the 2 Shipping Tubes (No. D), 8 Allen Bolts (No. 15), 8 Flat Washers (No. 30) and 8 Spring Washers (No. 36) from the Main Frame (No. 1) by Allen Wrench (No. 117). Attach the Front Stabilizer (No. 4) and Rail Frame (No. 3) onto the Main Frame (No. 1) using 8 Allen Bolts (No.
We value your experience using Sunny Health and Fitness products. For assistance with parts or troubleshooting, please contact us at support@sunnyhealthfitness.com or 1-877-90SUNNY (877-907-8669). STEP 2: Remove 6 Allen Bolts (No. 15), 6 Spring Washers (No. 36) and 6 Arc Washers (No. 35) from the Main Frame (No. 1). Slide the Mast Cover (No. 50) onto the Handlebar Post (No. 2). Connect the Sensor Extension Wire 2 (No. 70) with the Sensor Extension Wire 1 (No. 69).
We value your experience using Sunny Health and Fitness products. For assistance with parts or troubleshooting, please contact us at support@sunnyhealthfitness.com or 1-877-90SUNNY (877-907-8669). STEP 3: Remove 2 Hex Bolts (No. 17), 2 Spring Washers (No. 36), 2 Flat Washers (No. 32) and 2 Wave Washers (No. 73) from the Long Axle (No. 46). Insert the Long Axle (No. 46) into the Handlebar Post (No. 2), then insert 2 Wave Washers (No. 73) that were removed to the both sides of Long Axle (No. 46).
We value your experience using Sunny Health and Fitness products. For assistance with parts or troubleshooting, please contact us at support@sunnyhealthfitness.com or 1-877-90SUNNY (877-907-8669). STEP 4: Attach the 2 Pedal Arms (No. 9L/R) to 2 Roller Arms (No. 7) with 2 Pedal Hinge Bolts (No. 21), then put on 2 Flat Washers (No. 34) and 2 Nylon Nuts (No. 22) to the end of 2 Pedal Hinge Bolts (No. 21) by Allen Wrench (No. 119) and Spanner (No. 115). NOTE: Do not tighten the Pedal Hinge Bolts (No.
We value your experience using Sunny Health and Fitness products. For assistance with parts or troubleshooting, please contact us at support@sunnyhealthfitness.com or 1-877-90SUNNY (877-907-8669). STEP 5: Attach the 2 Handlebars (No. 11L/R) to 2 Swing Bars (No. 5L/R) respectively with 4 Carriage Bolts (No. 12), 4 Arc Washers (No. 35) and 4 Cap Nuts (No. 77) by Spanner (No. 116). Remove 4 Phillips Tapping Screws (No. 27) from 2 Cover for Left Swing Bar (No. 51L/R) and 2 Cover for Right Swing Bar (No.
We value your experience using Sunny Health and Fitness products. For assistance with parts or troubleshooting, please contact us at support@sunnyhealthfitness.com or 1-877-90SUNNY (877-907-8669). STEP 6: Remove 4 Phillips Screws (No. 74) from the Meter (No. 68) by Spanner (No. 116). Plug the Pulse Wire (No. 72) to the designed socket at back of the Meter (No. 68). Then Connect the Sensor Extension Wire 2 (No. 70) with Meter Wire A (No. 68a). Attach the Meter (No. 68) to the bracket of Handlebar Post (No.
ADJUSTMENT GUIDE HOW TO MOVE THE ELLIPTICAL There are transportation wheels located on the Front End Caps (No. 56L/R). Hold the Handlebar (No. E) of the Rail Frame (No. 3) and pull forward to lift the rear of the elliptical off the floor. Now you can move the elliptical. ADJUSTING THE BALANCE In order to achieve a smooth and comfortable ride, you must ensure that the elliptical is stable and secured. If you notice that the elliptical is unbalanced during use, you should adjust the Adjustable Pads (No.
IMPORTANT ELLIPTICAL INFORMATION WARNING: This elliptical requires a power source of 1 amp (100-240V) in order to properly operate. For your safety, as well as the safety of others, please verify that the power source is correct before plugging in the equipment. Any power source above or below this level could cause significant damage to the equipment and or user. OPERATING INSTRUCTIONS Plug the adaptor into the elliptical and into the outlet. The meter will turn on.
TIME: Accumulates the workout time from 0:00 to 99:59. Users can preset the target time they want. DIST (DISTANCE): Accumulates the workout distance from 0.00 to 999.9 Miles. Users can preset the target distance they want to reach. ODO (ODOMETER): Displays the total accumulated distance from 0 to 9999 Miles. CAL (CALORIES): Accumulates the calories burned from 0 to 9999. Users can preset the target calories they want to burn. WATT: Displays current watt.
CAL (CALORIES) 0.00~9995 0.00 ±5.00 1..When display is set as 0.00, CALORIES will count up. 2. When CALORIES is set as 5.00~9995, it will count down to 0.00. WATT 50~250 100 ±5 User can set watt value only in the Watt Control Program. AGE 10~99 30 ±1 Target HR will be based on Age. When Heart Rate exceeds Target HR, the Heart Rate number will flash. TARGET HEART RATE 60~220 90 ±1 Setting Parameters for Target Heart Rate.
There are 12 pre-set programs ready for use. All program profiles have 16 levels of resistance. SETTING PARAMETERS FOR PRE- SET PROGRAMS 1. Select one of the Pre-set Programs using the UP or DOWN button, then press ENTER button. TIME will flash so the value can be adjusted using the UP or DOWN key. 2. Press the ENTER button to save value and move to the next parameter to be adjusted. Continue through all desired parameters, pressing the START/STOP button to begin the workout.
3. Press ENTER button to save the value and move to the next parameter to be adjusted. NOTE: If you set up the target time for workout, then the next parameter of DISTANCE cannot be adjusted. 4. Continue through all desired parameters, pressing the START/STOP button to start the workout. NOTE: Once the workout parameters count down to zero, it will beep and stop the workout automatically. 5. Press the START button to continue the workout to reach the unfinished workout parameter.
TARGET HEART RATE PROGRAM (P16) Program Profile SETTING PARAMETERS FOR TARGET HEART RATE PROGRAM 1. Select TARGET HR (P16) using the UP or DOWN button, then press ENTER button. 2. TIME will flash. The value can be adjusted using the UP or DOWN button. 3. Press the ENTER button to save the value and move to the next parameter to be adjusted. NOTE: If you set up the target time to workout, then the next parameter of DISTANCE cannot be adjusted. 4.
USER PROGRAM Program Profile (P21-P24) The 4 user programs allow the user to set their own program that can be used immediately. SETTING PARAMETERS FOR USER PROGRAM 1. Select the User Program using the UP or DOWN button then press ENTER button. 2. TIME will flash so the value can be adjusted using the UP or DOWN button. 3. Press the ENTER button to save the values and move to the next parameter to be adjusted.
TROUBLESHOOTING PROBLEM E1-1 E1-2 E1-3 POSSIBLE CAUSE CHECK Check if all the cables are well plugged in or check if The motor couldn’t find the pins on the cables are its start point. improperly inserted. Or check if the motor is well connected. Check if all the cables are The motor signal has well plugged in or check if Plug in the cables again the pins on the cables are no induction. or change a new motor. improperly inserted. Or check if the motor is stuck.
EXPLODED DIAGRAM 1 19
EXPLODED DIAGRAM 2 20
PARTS LIST No. Description Spec. Qty. No. Description Spec. Qty. 1 Main Frame 1 34 Flat Washer D12×Φ24 2 2 Handlebar Post 1 35 Arc Washer Φ20×D8.5×R25 12 3 Rail Frame 1 36 Spring Washer D8 20 4 Front Stabilizer 1 37 Bearing 6900ZZ 4 1 PR. 38 Roller Axle 5L/R Swing Bar 2 Φ18×Φ10x11 6 Fixed Handlebar 1 39 Alloy Bushing 7 Roller Arm 2 40 Roller Spacer 4 8 Roller Arm Joint 2 41 Bottle Holder 1 9L/R 10 11L/R Pedal Arm 1 PR.
No. Description Spec. Qty. No. Description Spec. Qty. Φ28×Φ16.4x16 4 96 Crank Cap 2 1 67 Plastic Bushing 68 Meter 1 97 Pivot Bolt 68a Meter Wire A 1 98 Tension Spring Φ18×Φ2.
23
