www.trust.
ICS-2000 CONFIGURATION OF THE SECURITY SYSTEM Item 71110 Version 1.0 Visit www.trust.
ICS-2000 INTERNET CONTROL STATION A A 1. Preparation Make sure your phone / tablet is connected to the same network as the ICS-2000 A To verify this, check in the settings if the connectivity is displaying local. If this is not the case, connect to the Wi-Fi network of the router to which your ICS-2000 is connected to.
ICS-2000 INTERNET CONTROL STATION C B B Unscrew the siren cap, open the contact sensors and remove the motion sensor(s) from the holders. C Keep the included pin ready for pressing the pairing button.
ICS-2000 INTERNET CONTROL STATION B 2 sec learn button C 6 sec 1 sec A 1.1 Connect a new security system By connecting the security system with the Octopus control station it is possible to operate it with your smartphone / tablet and receive push notifications when the alarm is activated.
ICS-2000 INTERNET CONTROL STATION F D E D The Siren is now being paired to the control station E The Siren is now paired to the control station F Another dialog is displayed to add a device. Press the DOOR / WINDOW SENSOR. A new dialog is displayed to give a name for the door / window sensor. Enter a name and press ADD.
ICS-2000 INTERNET CONTROL STATION G I H G Press the SET button on the sensor for about 2 sec. Then press the CONNECT button. H The sensor is paired to the control station I Another dialog is displayed to add a device. Press the MOTION SENSOR. A new dialog is displayed to give a name for the motion sensor. Enter a name and press ADD. J Press the SET button on the sensor for about 2 sec. Then press the CONNECT button.
ICS-2000 INTERNET CONTROL STATION J K J K K Another dialog is displayed to add a device. When you are done adding sensors, press the button I’M DONE. The security system is now being added. This may take some time (1-2 minutes) L Optional: Add Remote. It is not a requirement to add the remote control. You can control the security system completely with the App. To add the remote follow the steps in section 1.
ICS-2000 INTERNET CONTROL STATION A B 1.2 Security system interface After adding the security system the overview screen will be displayed A On / Off switch: With this switch the system can be turned on or off. B System Status: The status of the system is shown. There are six different states. Security System: The security system is off. The sensors will not trigger the alarm. Sensors check: The status of the sensors are checked and the walk-out time is started Walk-out time: The walk-out time is active.
ICS-2000 INTERNET CONTROL STATION C C Sensor status: When the system is turned on or off, the status of the sensors are checked and displayed. : Sensor is active Anti-tamper switch is activated : Sensor is not active : Sensor has no connection : Battery of the sensor is almost empty When the system is activated and one of the sensors or siren indicates an error the status of the system will change to activation error. Turn the system off and on again.
ICS-2000 INTERNET CONTROL STATION A B 1.3 Turn the security system ON/OFF Ensure when you turn on the security system the anti-tamper switch of the siren is well pressed and that the motion sensor is securely mounted onto the holder. A Press the ON switch in the App or ON on the remote control to turn the security system on. The switch will open and become green, the status will change to “Checking Sensors”. All sensors will be checked.
ICS-2000 INTERNET CONTROL STATION A B C 1.4 Add a new sensor or remote A Press the + button to add an additional sensor or remote control B A dialog box will appear in order to select a sensor or a remote control which to be added. Press the desired sensor or remote control. Enter a name and press ADD. C Follow the instructions in the next dialog and press CONNECT. When you finished adding a sensor or remote control the security system will reconfigure.
ICS-2000 INTERNET CONTROL STATION C B A 1.5 Delete a sensor or remote A To remove a sensor (in IOS) slide your finger from right to left over the sensor which you want to delete. For the removal of a sensor in Android press 2 seconds on the name of the sensor. B A dialog appears to confirm whether to delete the sensor or remote control. Press YES to delete the sensor or remote control. The sensor or remote control is now removed. C In the overview the chosen sensor removed.
ICS-2000 INTERNET CONTROL STATION C B A 1.6 Update the security system The update function updates the security settings. This may take some time (2-3 minutes). Please only use this feature when it is adviced by our customer care department. A To update the security system, press the SETTINGS button in the menubar. Then press SECURITY SYSTEM UPDATE. B A dialog appears asking if you want to proceed with updating the security system. Press YES. C The security system is now being updated.
ICS-2000 INTERNET CONTROL STATION C B A 1.7 Delete the security system The delete function can be used if you want to start over. All security sensors needs to be reconnected. Note: before you restart please reset all sensors, remote control and siren. A To DELETE the security system, press the SETTINGS button in the menubar. Then press DELETE SECURITY SYSTEM. B A dialog appears asking if you want to proceed with deleting the security system. Press YES. C The security system is now being deleted.
ICS-2000 INTERNET CONTROL STATION FAQ Q: I keep getting an “activation error” on the motion sensor. A: Check if the motion sensor is properly mounted into its wall holder. Push the holder into the holes and slide the motion sensor down until you hear a click. Tis is clearly illustrated in the manual of the sensor. Q: I keep getting an “activation error” on the siren. A: Make sure the anti-tamper switch on the bottom of the siren is properly pressed and that the cap is screwed tight.
