INSTALLATION MANUAL TRUE manufacturing co., inc. underbar refrigeration CONGRATULATIONS! You have just purchased the finest commercial refrigerator available. You can expect many years of trouble-free operation.
TRUE www.truemfg.com underbar refrigeration NOTICE TO CUSTOMER Loss or spoilage of products in your refrigerator/ freezer is not covered by warranty. In addition to following recommended installation procedures you must run the refrigerator/freezer 24 hours prior to usage. SAFETY INFORMATION How to Maintain Your True Refrigerator to Receive the Most Efficient and Successful Operation. You have selected one of the finest commercial refrigeration units made.
TRUE www.truemfg.com underbar refrigeration DANGER! RISK OF CHILD ENTRAPMENT PROPER DISPOSAL OF THE REFRIGERATOR Child entrapment and suffocation are not problems of the past. Junked or abandoned refrigerators are still dangerous… even if they will sit for “just a few days.” If you are getting rid of your old refrigerator, please follow the instructions below to help prevent accidents. BEFORE YOU THROW AWAY YOUR OLD REFRIGERATOR OR FREEZER: • Take off the doors.
TRUE www.truemfg.com underbar refrigeration INSTALLATION OWNERSHIP To ensure that your unit works properly from the first day, it must be installed properly. We highly recommend a trained refrigeration mechanic and electrician install your TRUE equipment. The cost of a professional installation is money well spent. ELECTRIC INSTALLATION & SAFETY INFORMATION • If the supply cord is damaged, it must be replaced by a special cord or assembly available from the manufacturer or its service agent.
TRUE www.truemfg.
TRUE www.truemfg.com underbar refrigeration LOCATING SEALING CABINET TO FLOOR A. Use a Phillips screw diver and remove four screws from the L-bracket connected the unit to the wood skid (see image 1). Then use a 3/8” socket or wrench and remove the L-bracket from the unit (see image 2). STEP 1 - Position Cabinet - Allow one inch between the wall and rear of the refrigerated Bar Equipment to assure proper ventilation.
TRUE www.truemfg.com underbar refrigeration SETUP STANDARD ACCESSORIES SHELF INSTALLATION: For Proper Shelf Clip Installation Please Read The Following Instructions. SHELVING AND BIN DIVIDER INSTALLATION / OPERATION STEP 1 SHELF INSTALLATION: Install the top tab of the shelf clip into the proper hole. Push up on the bottom of the clip. (See image 1). A. Hook shelf clips onto shelf standards. STEP 2 B. Bottom tab of the shelf clip will fit tightly.
Horizontal bottle coolers are shipped with bin dividers in place. If it is necessary to adjust spacing the following procedure is recommended. A. Dividers are spring loaded - push divider towards rear of the cooler to release from front grommeted holes. B. Lineup divider front pegs with desired holes and punch through interior tape lining of both top and bottom holes - bottom peg first (front holes are taped over to improve insulation values). C.
TRUE www.truemfg.com underbar refrigeration DIRECT DRAW DRAFT ARM INSTALLATION INSTALL DRAFT ARM On direct draws, the drain is located at the front of the cabinet. To plumb in the drain, connect 3⁄4" (2cm) P.V.C. pipe to the 3⁄4" (2cm) barbed fitting supplies with the unit. Place rubber washer over draft arm mounting holes in cabinet, put beer line connector down through hole. Next, secure draft arm with four screws.
TRUE www.truemfg.com underbar refrigeration TDD-1 CO2 KNOCK-OUT This instruction is TRUE’s recommended procedure for installing a remote CO2 container. Knockout Plug can be located at either location. REQUIRED TOOLS • Pliers 7 STEP 1 - Remove black knockout plug with a pair of pliers. NOTE: Knockout plug for CO2 line can be locate in two different areas. View diagram to locate these two areas. STEP 2 - Use drill and bit to bore hole straight back through wall into compressor compartment.
TRUE underbar refrigeration www.truemfg.com TDD-2, -3 AND -4 (AND CLUB-TOP MODELS) CO2 KNOCK-OUT This instruction is TRUE’s recommended procedure for installing a remote CO2 container. REQUIRED TOOLS • Pliers • Power Drill • Silicone Sealer • Drill bit, 1/2" STEP 1 - Remove black knockout plug with a pair of pliers. STEP 2 - Use drill and bit to bore hole through insulation while holding tool at a 30º angle. This should line up with a pre-punched hole in the compressor compartment.
TRUE www.truemfg.com underbar refrigeration SLIDE DOOR OPERATION (CABINET ADJUSTMENT) STEP 1 - Before removing slide door do not use the side latch. Tension on the door cord is needed to execute these operation instructions. Doors can not be removed unless placed in specific locations stated in these instructions. STEP 3 - After centering the door lift it up and tilt top of door towards the back of the unit so the rollers are out of the top channel.
TRUE www.truemfg.com underbar refrigeration STEP 5 - Slide left door to the right so right edge lines up with the end of the TRUE Logo located at the top of the door frame. See image 6. Then lift door out of track same way as image 4. TRUE Logo TO ADJUST SLIDE DOOR STEP 1 - After cabinet is installed in a final location and correctly leveled check for any openings when the slide doors are completely closed.
TRUE underbar refrigeration www.truemfg.com OPERATION STARTUP A. The compressor is ready to operate. Plug in the cooler. B. Temperature controls are factory-set to give refrigerators an approximate temperature of 35°F and glass chiller frosters have an approximate temperature of 0°F. Allow unit to function several hours, completely cooling cabinet before changing the control setting. RECOMMENDATION - Before loading product we recommend you run your TRUE unit empty for two to three days.
TRUE underbar refrigeration www.truemfg.com MECHANICAL TEMPERATURE CONTROLS COIL SENSING An evaporator coil sensing temperature control ensures that the evaporator coil will remain clear of frost and ice by not allowing the compressor to restart until the coil temperature is above the freezing temperature. This is considered an off cycle defrost.
TRUE www.truemfg.com underbar refrigeration WHEN TO MAKE AN ADJUSTMENT TO A MECHANICAL TEMPERATURE CONTROL We advise to make a mechanical temperature control adjustment only for a high altitude location.
TRUE www.truemfg.com underbar refrigeration INSTRUCTIONS: DANFOSS TEMPERATURE CONTROL ADJUSTMENT FOR HIGH ALTITUDE APPLICATIONS STEP 1 - Unplug cooler. STEP 2 - Remove the screws that secure the temperature control to the inset box. STEP 3 - To make these adjustments it may be necessary to remove the temperature control from the housing. NOTE: You may have to remove the wires attached to the control. Take note as to which wire is on which spade terminal. STEP 4 - Pull out gently from cabinet.
TRUE www.truemfg.com underbar refrigeration CHART 1 2 3 4 5 CUT OUT 6 COLDER 7 CUT IN O 8 17 1 9 2 7 BUL. NO.
TRUE underbar refrigeration www.truemfg.com ELECTRONIC TEMPERATURE CONTROLS DANFOSS ELECTRONIC TEMPERATURE CONTROL GENERAL SEQUENCE OF OPERATION control probe = return air defrost probe = coil DANFOSS ELECTRONIC CONTROL REFRIGERATOR WITHOUT DIGITAL DISPLAY GENERAL SEQUENCE OF OPERATION 1. Cabinet is plugged in. a. Interior lights will illuminate on glass door models only. If the lights do not come on verify the light switch is in the “ON” position.
TRUE underbar refrigeration www.truemfg.com DANFOSS ELECTRONIC CONTROL FREEZER / GC WITHOUT DIGITAL DISPLAY GENERAL SEQUENCE OF OPERATION 1. Cabinet is plugged in. a. Interior lights will illuminate on glass door models only. If the lights do not come on verify the light switch is in the “ON” position. Solid door cabinets may or may not have lights that may be controlled by the door switch. b. Cabinet will start in a Defrost Cycle.
TRUE underbar refrigeration www.truemfg.com SOLLATEK ELECTRONIC TEMPERATURE CONTROL GENERAL SEQUENCE OF OPERATION control probe = return air defrost probe = coil SOLLATEK ELECTRONIC TEMPERATURE CONTROL GENERAL SEQUENCE OF OPERATION 1. Cabinet is plugged in. a. Interior lights will illuminate on glass door models only. If the lights do not come on verify the light switch is in the “ON” position. Solid door cabinets may or may not have lights that may be controlled by the door switch. 2.
TRUE www.truemfg.com underbar refrigeration STORAGE AND HANDLING PRESSURE Draft beer should be treated as a food product. In most instances draft beer is not pasteurized. It is very important that you store and handle it properly. Dispensing pressures differ according to: Follow these steps to ensure the highest quality and consumer satisfaction. • Draft beer should be immediately stored in a refrigerated cabinet. • Draft beer products have a recommended shelf life.
TRUE www.truemfg.com underbar refrigeration MAINTENANCE, CARE, CLEANING CLEANING THE CONDENSER COIL IMPORTANT WARRANTY INFORMATION When using electrical appliances, basic safety precautions should be followed, including the following: Condensers accumulate dirt and require cleaning every 30 days. Dirty condensers result in compressor failure, product loss, and lost sales, which are not covered by warranty.
TRUE www.truemfg.com underbar refrigeration STAINLESS STEEL EQUIPMENT CARE AND CLEANING 8 STEPS THAT CAN HELP PREVENT RUST ON STAINLESS STEEL: CAUTION: Do not use any steel wool, abrasive or chlorine based1. products to clean stainless steel surfaces. STAINLESS STEEL OPPONENTS There are three basic things which can break down your stainless steel’s passivity layer and allow corrosion to rear its ugly head. 1. Scratches from wire brushes, scrapers, and steel pads are just2.
TRUE www.truemfg.com underbar refrigeration GENERAL MAINTENANCE DRAFT BEER PROBLEMS To minimize draft beer problems, always follow the recommended instructions for temperature and CO2 pressures from your beer supplier. FLAT BEER - DESCRIPTION: FOAMY HEAD DISAPPEARS QUICKLY. BEER LACKS USUAL ZESTFUL BREWERY FRESH FLAVOR. • CO2 turned off when not in use. • Contaminated air source (associated with compressed air). • Greasy glasses. • Not enough pressure. • Pressure shut off during night.
TRUE www.truemfg.com underbar refrigeration CHANGING CO2 GAS CYLINDER FOLLOW THESE INSTRUCTIONS AT ALL TIMES WHEN YOU REPLACE A CO2 GAS CYLINDER: NOTE 1. Close cylinder at "A". 2. Remove tap "D" from barrel. Pull pressure release ring on body of tap to release pressure remaining in line. (Do not close "C") It requires 1/2 pound CO2 to dispense 1/2 barrel of beer at 38˚F with 15 pounds pressure on barrel. 3. Remove or loosen regulator key "B" by turning counter clockwise. 4.
TRUE www.truemfg.com underbar refrigeration CLEANING BAR SYSTEM Draught dispensers, regardless of design, must be cleaned at least every two weeks. Flushing your draught dispenser with water only is not enough. NOTE Use cleaners approved by your beer supplier and follow their instructions. If you are using the cleaning kit purchased from TRUE follow these instructions: Cleanliness should be constantly maintained in your dispenser so that your draught beer will be at its best when served.
TRUE underbar refrigeration www.truemfg.com LIGHT BULB REPLACEMENT (IDL) INTEGRATED DOOR LIGHTING WARNING: When replacing a light bulb make sure power to the unit is either turned off or unplugged. IDL (INTEGRATED DOOR LIGHTING): • Squeeze the plastic lampshield together and pull away from the door (See Image 1). • Push the bulb down while pulling the spring activated lampholder up. This will give you enough clearance to take the bulb out (See Image 2). 1 Remove the lampshield to reveal the bulb.
TRUE www.truemfg.com underbar refrigeration WARRANTY INFORMATION (U.S.A. & CANADA ONLY!) THIS WARRANTY ONLY APPLIES TO UNITS SHIPPED FROM TRUE'S MANUFACTURING FACILITIES AFTER SEPTEMBER 1, 2015.
