Data Sheet

POWER - NIKKOHM
TO220 50W HIGH POWER RESISTORS
TCP50U
Specifications
TCP50U
Test Conditions
Rated Power 50 Watt -55 °C to 25 °C flange temperature
Rating Power 1 Watt Free air.
Heat Resistance 2.3 °C/W Hot spot to flange
Resistance Range 0.02-0.09ohm 0.1-510 k ohm 10-51Kohm Note 2
Nominal Resistance E6 E24+ E24+ Include 2.5, 4.0, 5.0, 8.0 and 16
TCR, ppm/°C >250 (H) 100 (A) 50 (C) Note 3
Tolerance 5%(J) 1% (F), 5% (J) +/-1% (F) 1% tolerance at 0.01-0.091 ohm is available optionally.
Resistor Material Thick Film Thin Film
Capacitance 1.69pF Equivalent parallel capacitance.
Inductance 9.65nH Equivalent series inductance
Operation Temp. -55 °C to +175 °C
Max. Operating Volt. smaller either 700V or
RP 
P is rating power and R resistance
Withstanding Voltage 2000VAC Terminal and flange, 60 seconds, 1mA
Load Life +/- 1.0 % 25 °C, 90 min. ON, 30 min. OFF, 1000 hours.
Humidity +/- 1.0 % 40 C°, 90-95%RH, DC 0.1W, 1000 hours.
Temp. Cycle +/- 0.25 % -55 °C,30 min.,+155 °C,30 min., 5cycles
Soldering Heat +/- 0.1 % 350+/-5 °C, 3seconds,
Solder ability Over 95% of surface 230+/-5 °C, 3seconds.
Insulation Resistance Over 1,000 Meg ohm Between terminals and flange.
Vibration +/- 0.25 % IEC60068-2-6, see note 4
Weight 2.1 grams
Derating Temperature Rise
Frequency Characteristics
RoH
S
Note:
(1) Insulation material is unnecessary between flange and heat-sink, flange and resistor is separated by alumina substrate.
(2) Resistance measurement shall be made at a point 5.27mm +/-0.6 mm from the resistor body.
(3) TCR of low resistance will be increased as 300ppm/0.02ohm, 200ppm/0.05ohm, 140ppm/0.1ohm and 80ppm/0.2ohm typically.
Testing point is at 5.27mm from bottom of molding of terminals.
(4) Test method is IEC60068-2-6, and specification is sine sweep wave form, 100Hz-2000Hz, 10 cycles, amplitude 0.75mm or 100m/s
2
,
90minutes. direction x-y z, Amplitude 0.75mm will be applied under break point Frequency (about 60Hz) and 100m/ s
2
over break
point
(5) When mounting resistor on heat-sink by screw, clip and pressure strip with using heat conduction grease on back side of resistor are
recommended. Recommended screw torque is 0.5-0.6Nm.
Temperature Rise °C
)
140
TCP50UC500 F
120
100
Hot spot temperature on resistor based
80
referenced from flange temperature
.
60
40
20
0
0 10 20 30 40 50
Power (Watt
)
Impedance (ohm)
1k
TCP50U C1K0F
TCP50U C101F
100
TCP50U C100F
10
TCP50U C500F
TCP50U C220F
1
100k 1M 10M 100M 1G 10G
Frequency (Hz)
Pulse Energy Durability
10n 100n 1u 10u 100u 1m 10m 100m 1 10 100
Pulse width (seconds)
100k
10k
1k
100
10
Pulse peak power (W)
Applied to TCP50UC10ohmF
and resistance < 100ohm
Tentative continuous-pulse power allowance at duty 0.01.
Additional load life test will be necessary in actual equipment,
Because curve will be changed by resistance, repetition, duty and
o
p
eratin
g
tem
p
erature.
400W
50W
50
40
30
20
10
0
-55 0 50 100 150 200
Flange Temperature (°C)
+25°C
+175°C
Rating Power (W)
Nikkohm Co., Ltd. 3-31-2640 Minamicho, Misawa, Aomori 033-0036 Japan TEL: [phone], FAX: [phone]
© Nikkohm Co., Ltd. All rights reserved. 2014. URL: http://www.nikkohm.co.jp & http://www.nikkohm.co.jp / e-mail: [e-mail]
Conrad Electronic SE - Klaus-Conrad-Str.1 - 92250 Hirschau - www.conrad.de