Datasheet

ManualsBrandsTRU COMPONENTS ManualsMotion SensorsInductive proximity sensor M30 shielded PNP NC TC-TS30-10P-2

Distributed by Conrad Electronic SE • Klaus-Conrad-Str. 1 • D-92240 Hirschau

Datasheet

Item no. TC-TS30-10N-1,2, TC-TS30-10P-1,2

TC-TS30-15N-1, 2, TC-TS30-15P-1,2

V1_09062017_01_en

This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).

All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or the capture in electronic data processing systems require the prior

written approval by the editor. Reprinting, also in part, is prohibited. This publication represents the technical status at the time of printing.

Specifications

Item Standard

Differential travel 10% max. of sensing distance

Target Ferrous metal (The sensing distance decreases with non-ferrous metal.)

Power supply voltage 12 ～ 24 VDC. Ripple (p-p) : 10% max.

(operating voltage range) (10 ～ 30 VDC)

Current consumption (DC 3-wire) 10 mA max.

Output type See product selection

Control load current output (See note 1.) 200 mA max. (32 Vdc max.)

Residual voltage 1 V max. (under load current of 200 mA with cable length of 2 m)

Operation mode See product selection

(with sensing object approaching)

Protection circuit Output reverse polarity protection, power source circuit reverse

polarity protection,

Surge suppressor, Short-circuit protection

Ambient air temperature Operating: -40°C to 70°C, Storage: -40°C to 80°C( with no icing or condensation)

Temperature influence (See note 1.) ±10% max. of sensing distance at 23°C within temperature range of -25°C to 70°C

±15% max. of sensing distance at 23°C within temperature range of -40°C to 70°C

Ambient humidity Operating : 35% to 95%, Storage : 35% to 95%

Voltage influence ±1% max. of sensing distance in rated voltage range ±15%

Insulation resistance 50MΩ min. (at 500 VDC) between current carry parts and case

Dielectric strength 1,000 VAC at 50/60 Hz for 1 min between current carry parts and case

Vibration resistance 10 to 55 Hz, 1.5mm double amplitude for 2 hours each in X, Y and Z directions

Shock resistance 1,000 m/s2, 10 times each in x, Y and Z directions

Note 1. When using any model at an ambient temperature between -40°C and -25°C and a power voltage between

30 and 32 VDC, use a load current of 100 mA max.,

Summary of content (3 pages)

PAGE 1
Distributed by Conrad Electronic SE • Klaus-Conrad-Str. 1 • D-92240 Hirschau Datasheet Item no. TC-TS30-10N-1,2, TC-TS30-10P-1,2 TC-TS30-15N-1, 2, TC-TS30-15P-1,2 V1_09062017_01_en Specifications Item Differential travel Target Power supply voltage (operating voltage range) Current consumption (DC 3-wire) Output type Control load current output (See note 1.) Residual voltage Standard 10% max. of sensing distance Ferrous metal (The sensing distance decreases with non-ferrous metal.) 12 ～ 24 VDC.
PAGE 2
Distributed by Conrad Electronic SE • Klaus-Conrad-Str. 1 • D-92240 Hirschau Datasheet Item no. TC-TS30-10N-1,2, TC-TS30-10P-1,2 TC-TS30-15N-1, 2, TC-TS30-15P-1,2 V1_09062017_01_en Product selection TS 30 - □ □ - □ 2. Dimension of sensing face 1 2 3 4 5 TS Type series 1. Housing outline 30 : diameter 30 mm TS: Inductive thread round 3. Sensing distance 4. Output stage Numeral : Sensing distance : N : NPN open collector DC mode P : PNP open collector DC mode 10 = 10 mm ± 10%, 15 = 15 mm ± 10%, 5.
PAGE 3
Distributed by Conrad Electronic SE • Klaus-Conrad-Str. 1 • D-92240 Hirschau Datasheet Item no. TC-TS30-10N-1,2, TC-TS30-10P-1,2 TC-TS30-15N-1, 2, TC-TS30-15P-1,2 Item Output Function Output Stage NPN NO - output NPN NC - output PNP NO - output PNP NC - output Sensing distance Setting distance Response frequency Standard target Body material Circuit protection Reverse polarity protection of supply voltage Cable length Shield Cable type TS30-10N-1 TS30-10N-2 TS30-10P-1 TS30-10P-2 10 mm ± 10% 0 to 8.