Certificate

ManualsBrandsTRU COMPONENTS ManualsToggle & Rocker SwitchesToggle switch 250 Vac 3 A 1 x Off/On

22B - During the wiring installation for M4 Screw, the switch terminals need to fix by jig or tool before screw tightly.

9A - The lighted switches rated DC rating only employing DC lamps; the lighted switches rated AC rating only employing AC lamps.

9B - The Switch body is installed inside of end product; only consider the Actuator as accessible parts.

9C - Heating test was conducted at ambient temperature of 85 deg C with measured maximum temperature of 108.8 deg C on terminals, the

suitability of wire conductors using on the switches terminals shall be determined in end-product applications.

9D - After 6K Endurance cycles, the switches rated 20RA, 125 V ac were evaluated for temperature test at 18 A only.

9E - The switches get a protection degree of IP 66 in accordance with the manufacturer's mounting means only. For IP 6X dust test, talcum powder

did enter the mounting enclosure and deposited on terminals of the switch but the talcum powder did not enter the switch housing. The suitability

of mounting means for the switches shall be determined in end-product applications.

A2 - The construction applied for the rating 16 A and 14 A is different. The spring with 12.5 mm long is used for 14/10 A, 125/250 V ac; 1/3 hp,

125 V ac; 1/2 hp, 250 V ac. The spring with 13.3 mm long is used for 16/10 A, 125/250 V ac; 1/3 hp, 125 V ac; 1/2 hp, 250 V ac.

A3 - Waterproof should be evaluated for compliance with the end-use product Standard.

Note 1 - The switch terminals have not been investigated for printed circuit board connections. The suitability of these terminals should be

evaluated for compliance with end-use product standard.

Note 10 - The Models R13-112B8W, R13-112C8 and R13-112A8 had a water proof cover part, but were not tested as part of this investigation. The

suitability of the water proof cover must be determined in accordance with the end product Standard.

Note 10A - When mounted in accordance with the manufactures instruction, this switch gets a protection degree of IP 40.

Note 10B - The Switch body is installed inside of end product; only consider the Actuator as accessible parts.

Note 10C - Heating test was conducted at ambient temperature of 85 deg C with measured maximum temperature of 101.8 deg C on terminals,

the suitability of wire conductors using on the switches terminals shall be determined in end-product applications.

Note 11 - The screw terminals are not intended to be used for wire binding. They are intended to be used with crimp-on type connectors only.

Note 11A - When mounted in accordance with the manufactures instruction, this switch gets a protection degree of IP 65 for Proof Bushing

Construction with mounting enclosure opening 19.2 mm by 13 mm as mounting means, others gets IP40.

Note 11B - The Switch body is installed inside of end product; only consider the Actuator as accessible parts.

Note 11C - Heating test was conducted at ambient temperature of 85 deg C with measured maximum temperature of 111.1 deg C on terminals,

the suitability of wire conductors using on the switches terminals shall be determined in end-product applications.

Note 12 - These are lighted switches employing a lamp. The usable lamp life has not been evaluated.

Note 14B - Heating test was conducted at ambient temperature of 85 degC with measured maximum temperature of 127.4 degC on terminals, the

suitability of wire conductors using on the switches terminals shall be determined in end-product applications.

Note 16A - IP65 and IP40 - for accessible parts and enclosure of the end product enclosure when mounted or installed according to the

manufacturer's directions. Internal parts were not evaluated for IP ratings and must be considered in the end product.

Note 16B - The Switch body is installed inside of end product; only consider the Actuator as accessible parts.

Note 16D - Heating test was conducted at ambient temperature of 85 deg C with measured maximum temperature of 100.5 deg C on terminals,

the suitability of wire conductors using on the switches terminals shall be determined in end-product applications.

Note 17A - The Switch body is installed inside of end product; only consider the Rocker as accessible parts.

Note 17B - Heating test was conducted at ambient temperature of 85 degC with measured maximum temperature of 121.2 degC on terminals, the

suitability of wire conductors using on the switches terminals shall be determined in end-product applications.

Note 17C - The Printed Wiring Board assembly has not been evaluated, the acceptability for use with end-product and spacings shall be determined

in the end-product application.

Note 17D - IP 52 testing was completed on the exposed switch parts and gasket to the end product enclosure. The mounting method was a

rectangular opening 36.2 by 21.0 mm with material 3.1 mm thick. Internal parts were not evaluated for IP ratings and shall be considered in the

end product.

Note 19A - IP40 - for accessible parts and enclosure of the end product enclosure when mounted or installed according to the manufacturer's

directions. Internal parts were not evaluated for IP ratings and must be considered in the end product.

Note 19B - The Switch body is installed inside of end product; only consider the Rocker/Lens as accessible part for T85/55.

Note 19C - Heating test was conducted at ambient temperature of 85 deg C with measured maximum temperature of 100.5 deg C on terminals,

the suitability of wire conductors using on the switches terminals shall be determined in end-product applications.

Note 2 - The suitability of the actuator button material as an enclosure has not been investigated.

Note 2A - UL61058-1 - These switches employ Quick Connected or Soldered terminals, the terminals have been investigated for use with stranded

conductors of specified sizes 2.5 mm2 only for all cat. nos.

Note 2B - UL61058-1 - These switches employ Quick Connected or Soldered terminals, the terminals have been investigated for use with Rigid

conductors of specified sizes 4.0 mm2 only for all cat. nos.

Note 2C - UL61058-1 - These are lighted switches employing a lamp. The usable lamp life has not been evaluated.

Note 2D - UL61058-1 - Heating test was conducted at ambient temperature of 85 deg C, the suitability of wire conductors using on the switches

terminals shall be determined in end-product applications.

Note 3 - Terminations other than solder connections should be evaluated for compliance with the end-use product standard.

Note 4 - The load is to be connected across the switch terminals in such a manner that each of the poles will break the same circuit, see Appendix

FS, circuit B.

Note 4A - UL61058-1 - When mounted in accordance with the manufactures instruction, this switch gets a protection degree of IP40, also if Dust

cover removed, IP40 still available.

Note 4B - UL61058-1 - The switch is to be employed in an end use product providing an enclosure or insulating barrier that provides Reinforced or

Double Insulation over the front and rear switch enclosure Surfaces.

Note 4C - UL61058-1 - These are lighted switches employing a lamp across disconnection terminal "b".

Page 2

of 2

WOYR2.E67774 - Switches, Appliance and Special Use - Component

20.06.2018htt

://database.ul.com/c

in/XYV/tem

late/LISEXT/1FRAME/show

e.html?na

...