Certificate

3 250 60 GP 6K
7 125 60 GP 6K
6 250 60 GP 6K
R13-69 f/b A-C, AC or BC, f/b 01 or 05; R13-70, f/b A, B, BF, C, D, F, H or I, f/b 01 or 05; R13-91, f/b A, B, BF, C, D,
F, H or I , f/b 01 or 05; R13-69P or R13-90P, f/b A-C, f/b A-C or L, f/b 01 or 05; R13-221, f/b A, B, BF, C, D, F, H or I,
may be f/b 1, 2 or 3, f/b 01 or 05
16 125 60 1/8hp 6K 85 M/M PP/- 2, Note 2
10 250 60 1/3hp 6K
R13-72, f/b A, B, C, D or I, f/b -01or -05
16 125 60 GP 6K 85 1/1 or 1/2 -/A Note 12
10 250 60 GP 6K
- 125 60 1/3hp 6K
- 250 60 1/2hp 6K
R13-73 f/b A, A1, B or C, f/b A-02; f/b -T85.
16 125 60 1/2hp 6K 85 1/M -/- Note 6
10 250 60 1/2hp 6K
R13-73 f/b A, B or C, f/b 1-4
8 125 60 GP 6K 65 2/1 PP/- 2, Note 3
4 250 60 GP 6K
R13-73AA-02-T120 8 120 60 TV 25K 120 2/1 PP/- -
R13-75A or R13-75C 10 125 60 GP 6K 65 2/M PP/- Note 2, 3
5 250 60 GP 6K
- 250 60 3/4hp 6K
R13-80A3, R13-80G3 15 125 60 GP 6K 65 2/2 -/- Note 2, 3
10 250 60 GP 6K
- 125 60 3/4hp 6K
- 250 60 3/4hp 6K
R13-87A-I, R13-87B, R13-87C, R13-87D f/b 02
16 125 60 1/3hp 6K 65 2/M PP/- 2, Note 5
10 250 60 1/2hp 6K
R13-87H, R13-87I 16 125 60 1/3hp 6K 85 2/M -/- 2, Note 5
10 250 60 1/2hp 6K
R13-901 6 125 60 GP 6K 55 1/1 -/- -
3 250 60 GP 6K
R13-915, R13-915B2 5 125 60 GP 6K 65 1/1 -/- -
- 250 60 1/4hp 6K
R13-918B-02 16 125 60 GP 6K 105 1/1 -/A -
10 250 60 GP 6K
- 125 60 1/3hp 6K
- 250 60 1/2hp 6K
R14-6S, R14-6Q w/ wo 1 or 2
5 125 60 GP 6K 65 1/1 -/- Note 1, 2, 3
3 250 60 GP 6K
16A - IP65 and IP40 - for accessible parts and enclosure of the end product enclosure when mounted or installed according to the manufacturers
directions. Internal parts were not evaluated for IP ratings and must be considered in the end product.
16B - The Switch body is installed inside of end product; only consider the Actuator as accessible parts.
16C - Heating test was conducted at ambient temperature of 85 deg C with measured maximum temperature of 119.7 deg C on terminals, the
suitability of wire conductors using on the switches terminals shall be determined in end-product applications.
20A - IP 4X testing was completed on the complete switch without an end product enclosure. The switch gasket (seal) to the end product enclosure
is evaluated in the end product testing.
22A - IP 40 testing was completed on the complete switch without an end product enclosure. The Inner Boot must be provided to maintain the
IP40 function. The switch gasket (seal) to the end product enclosure is evaluated in the end product testing.
Page 2
2
of 2
4
WOYR2.E67774 - Switches, Appliance and Special Use - Component
20.06.2018htt
p
://database.ul.com/c
gi
-
b
in/XYV/tem
p
late/LISEXT/1FRAME/show
p
a
g
e.html?na
m
...