Certifications

ManualsBrandsTRU COMPONENTS ManualsToggle & Rocker SwitchesToggle switch 250 Vac 10 A 2 x Off/On TC-R13-28F-01 latch 1 pc(s)

terminals should be evaluated for compliance with end-use product standard.

Note 10 - The Models R13-112B8W, R13-112C8 and R13-112A8 had a water proof cover part, but were not tested as part of

this investigation. The suitability of the water proof cover must be determined in accordance with the end product Standard.

Note 10A - When mounted in accordance with the manufactures instruction, this switch gets a protection degree of IP 40.

Note 10B - The Switch body is installed inside of end product; only consider the Actuator as accessible parts.

Note 10C - Heating test was conducted at ambient temperature of 85 deg C with measured maximum temperature of 101.8

deg C on terminals, the suitability of wire conductors using on the switches terminals shall be determined in end-product

applications.

Note 11 - The screw terminals are not intended to be used for wire binding. They are intended to be used with crimp-on type

connectors only.

Note 11A - When mounted in accordance with the manufactures instruction, this switch gets a protection degree of IP 65 for

Proof Bushing Construction with mounting enclosure opening 19.2 mm by 13 mm as mounting means, others gets IP40.

Note 11B - The Switch body is installed inside of end product; only consider the Actuator as accessible parts.

Note 11C - Heating test was conducted at ambient temperature of 85 deg C with measured maximum temperature of 111.1

deg C on terminals, the suitability of wire conductors using on the switches terminals shall be determined in end-product

applications.

Note 12 - These are lighted switches employing a lamp. The usable lamp life has not been evaluated.

Note 14B - Heating test was conducted at ambient temperature of 85 degC with measured maximum temperature of 127.4

degC on terminals, the suitability of wire conductors using on the switches terminals shall be determined in end-product

applications.

Note 16A - IP65 and IP40 - for accessible parts and enclosure of the end product enclosure when mounted or installed

according to the manufacturer's directions. Internal parts were not evaluated for IP ratings and must be considered in the end

product.

Note 16B - The Switch body is installed inside of end product; only consider the Actuator as accessible parts.

Note 16D - Heating test was conducted at ambient temperature of 85 deg C with measured maximum temperature of 100.5

deg C on terminals, the suitability of wire conductors using on the switches terminals shall be determined in end-product

applications.

Note 17A - The Switch body is installed inside of end product; only consider the Rocker as accessible parts.

Note 17B - Heating test was conducted at ambient temperature of 85 degC with measured maximum temperature of 121.2

degC on terminals, the suitability of wire conductors using on the switches terminals shall be determined in end-product

applications.

Note 17C - The Printed Wiring Board assembly has not been evaluated, the acceptability for use with end-product and spacings

shall be determined in the end-product application.

Note 17D - IP 52 testing was completed on the exposed switch parts and gasket to the end product enclosure. The mounting

method was a rectangular opening 36.2 by 21.0 mm with material 3.1 mm thick. Internal parts were not evaluated for IP ratings

and shall be considered in the end product.

Note 19A - IP40 - for accessible parts and enclosure of the end product enclosure when mounted or installed according to the

manufacturer's directions. Internal parts were not evaluated for IP ratings and must be considered in the end product.

Note 19B - The Switch body is installed inside of end product; only consider the Rocker/Lens as accessible part for T85/55.

Note 19C - Heating test was conducted at ambient temperature of 85 deg C with measured maximum temperature of 100.5

deg C on terminals, the suitability of wire conductors using on the switches terminals shall be determined in end-product

applications.

Note 2 - The suitability of the actuator button material as an enclosure has not been investigated.

Note 2A - UL61058-1 - These switches employ Quick Connected or Soldered terminals, the terminals have been investigated for

use with stranded conductors of specified sizes 2.5 mm2 only for all cat. nos.

Note 2B - UL61058-1 - These switches employ Quick Connected or Soldered terminals, the terminals have been investigated for

use with Rigid conductors of specified sizes 4.0 mm2 only for all cat. nos.

Page 40 of 4

SWITCHES, APPLIANCE AND SPECIAL USE - COMPONENT | UL Product iQ

08.04.201

htt

s://i

.ul

ros

ector.com/en/

rofile?e=16384