DH 15 AX TRT-BA-DH 15-TC-001-EN EN Operating Manual – Condenser dryer DH 15 AX TROTEC® GmbH & Co. KG • Grebbener Straße 7 • D-52525 Heinsberg Tel.: +49 2452 962-400 • Fax: +49 2452 962-200 www.trotec.com • E-Mail: info@trotec.
Table of contents Notes regarding the operating manual Notes regarding the operating manual .................................... 01 Symbols Information about the device................................................... 02 Hazardous electric current! Safety ..................................................................................... 05 Warns about hazards from electric current which can Transport, assembly and preparation for start-up.................... 06 lead to injuries or even death.
Device depiction Information about the device Description of the device 1 This device uses the principle of condensation to automatically dehumidify rooms. The fan sucks damp room air through the air inlet (5), the air filter (7), the evaporator and to the condenser located behind it. The air is cooled at the cold evaporator until it is below the dew point. Water vapour contained in the room air precipitates on the evaporator fins as either condensation or frost.
Technical data Parameter Value Model Dehumidifying capacity, max. Operating temperature Operating range for relative humidity Air flow rate, max. Electric connection Power input Fuse (home) Cooling agent Amount of cooling agent Weight Dimensions (HxDxW) Minimum distance from walls of other objects DH 15 AX 22 l / 24 h 0-40 °C 30-90 % 225 m³/h 230 V / 50 Hz 430 W 10 A R407c 0.
Circuit diagram N 1 4 L MAINS LAMP HUMIDISTAT 2 4 1 DEFROST C ONTROL STAT BLUE 1,0 3 R BRN 1,0 GRN/YEL BLU 1,0 BLU 1,0 BLACK FLYING LEAD IF IN DOUBT ASK GRN/YEL FLYING LEAD DO NOT SCALE PRINT HUMIDISTAT FLYING BLUE PNK 1,0 LEADS C GRN/YEL 1,0 230V MAINS LAMP 3 SOLENOID VALVE BLACK FLYING LEAD PNK 1,0 RED 1,0 DEFROST C ONTROL STAT 2 BLACK FLYING LEAD BLACK FLYING LEAD FAN MOTOR PNK 1,0 C IRCU IT D IA G R A M SOLENOID VALVE C FAN MOTOR R C OMPRESSOR BROW N FLYING LEAD
Intended use Only use the device DH 15 AX as a stationary industrial dryer for Read this manual carefully before starting or using the drying and dehumidifying room air, while adhering to and following the technical data. device. Store the manual near the device or its site of use! Safety Intended use encapsulates: • Do not use the device in potentially explosive rooms.
Danger! A falling device can cause injuries! Always utilize the help of another person to transport and assemble the device. Never stand below the device when suspended in the air. Ensure adequate stability of the device's wall fixing. Assemble the device as follows: Check the condensation drain hose for proper fit and adjust the hygrostat to the desired humidity level, before you put the protective housing back on the device. A. Behaviour in the event of an emergency 1.
C. F. 6 mm D. G. 6 mm E. H.
Storage Operating elements When out of use, store the device as follows: • dry, • with a roof overhead, • in an upright position where it is protected from dust and direct sunlight, • with a plastic cover to protect it from invasive dust, if necessary. • The storage temperature is the same as the range given for the operating temperature in the chapter Technical Data. 2 Operation • After being switched on, the device operates fully automatically.
Positioning the condensation drain hose Switch device on Note: 1. Ensure that the condensation drain hose has been laid and connected properly. Do not create tripping hazards. The condensation drain hose is already installed when the device is delivered. 2. Ensure that the condensation drain hose is not bent or jammed and that there are no objects on the condensation 1. Ensure that the condensation drain hose is properly connecdrain hose. ted to the device and is free of damage. 2.
The device gets very warm, is loud or is losing performance: • Check the air inlets and air filter are not dirty. Remove external The accurate functionality of the device was tested during producdirt. tion a number of times. However, if functionality faults do occur, • Check the inside of the device for dirt (see chapter Maintethen check the device according to the following list. nance). If necessary, clean the interior of the device using compressed air.
Maintenance Maintenance intervals Maintenance and care interval before every start Empty the condensate pump, condensation tray and/or condenser dryer check air inlets and outlets for dirt and foreign objects and clean if necessary clean housing visually check the inside of the device for dirt check air inlet grid and air filter for dirt and foreign objects and clean or replace if necessary replace air filter check for damages check attachment screws carry out a test run when neces- at least every at lea
Activities for before the start of maintenance Cleaning the housing 1. Do not touch the mains plug with wet or damp hands. 2. Before any work, detach the mains plug! 1. Use a soft, lint-free cloth for cleaning. 2. Dampen the cloth with clean water. Do not use sprays, solvents, alcohol-based or abrasive cleaners to dampen the Maintenance tasks at the electrical equipment or cloth.
PIPEWORK 95 01 02 06 10 TTW15AXONLY GRILLESFITTEDIN WALL BEHIND MACHINE 14 Overview and list of spare parts WARNING D isc o nn ec t t he m ains s upp ly b efo r e re m oving t his c o ve r 08 05 AIR FLOW 15 16 POSITION VARIES WITHEDITION 95 03 13 NOTEFANBLADE ORIENTATION 03 04 12 09 R407c 11 SUCTION PROCESS DISCHARGE Note! The position numbers of the spare parts differ from those describing the positions of other parts mentioned in this operating manual. No. Spare part No.
Disposal Declaration of conformity In the European Union, electronic equipment must not be treated as domestic waste, but must be disposed of professionally in accordance with Directive 2002/96/EC of the European Parliament and Council of 27th January 2003 concerning old electrical and electronic equipment. At the end of its life, please dispose of this instrument in a manner appropriate to the relevant legal requirements.
TROTEC® GmbH & Co. KG • Grebbener Straße 7 • D-52525 Heinsberg Tel.: +49 2452 962-400 • Fax: +49 2452 962-200 www.trotec.com • E-Mail: info@trotec.
