Model FT5000 (X2) QUICK REFERENCE GUIDE THIS AREA FOR SERVICE PROVIDER CONTACT INFORMATION: TDN 07100-00095B 06/2008
MANAGEMENT FUNCTIONS - ACCESS INSTRUCTIONS 1. AT ATM WELCOME SCREEN, PRESS AND HOLD DOWN THE KEY (L OWER - RIGHT CORNER OF KEYPAD ), PRESS <1> KEY , THEN RE LEASE BOTH KEYS . THE P ASSWORD ACCESS PROMPT IS DISPLAYED. 2. ENTER PASSWORD AND SELECT . THE MANAGEMENT FUNCTIONS MAIN MENU IS DISPLAYED. RESTART / SHUTDOWN TERMINAL FOLLOW ACCESS INSTRUCTIONS TO ENTER MANAGEMENT FUNCTIONS. SELECT SYSTEM PARAMETERS. RESTART TERMINAL: THIS FUNCTION REBOOTS THE TERMINAL.
DIAGNOSTICS FOLLOW ACCESS INSTRUCTIONS TO ENTER MANAGEMENT FUNCTIONS. SELECT DIAGNOSTICS > DISPENSER. PURGE: THIS INSTRUCTS THE DISPENSER TO REMOVE ANY NOTES (JAMS) IN FEED PATH. TEST DISPENSE: THIS INSTRUCTS THE DISPENSER TO DISPENSE MINIMUM ONE NOTE FROM EACH INSTALLED CASSETTE INTO THE REJECT CASSETTE / AREA . SELECT DIAGNOSTICS > PRINTER. RESET / TEST PRINTER: THIS INSTRUCTS THE PRINTER TO RE-INITIALIZE AND PERFORM A TEST PRINTOUT.
CASSETTE CLOSE FUNCTIONS (FRONT DISPLAY) FOLLOW ACCESS INSTRUCTIONS TO ENTER MANAGEMENT FUNCTIONS. SELECT TERMINAL CLOSE FUNCTIONS. SELECT CASSETTE CLOSE. AFTER CASSETTE(S) HAVE BEEN REINSERTED IN THE DISPENSER, PRESS . NOTE: FOR AN NMD-50/100 INSTALLED, WAIT FOR THE CASLOCK ( THIS IS DONE AUTOMATICALLY). PRESS IF APPLICABLE. SETTES TO THIS PLACE SELECTED CASSETTE(S) IN SERVICE.
CASSETTE CLOSE FUNCTIONS (REAR SERVICE PANEL) THE CASSETTE CLOSE FUNCTIONS OPERATE THE SAME AS THE FRONT DISPLAY SEQUENCE . FROM THE R EAR SERVICE PANEL: PRESS FROM THE RSP KEYPAD. W HEN PROMPTED , ENTER YOUR MANAGEMENT FUNCTION PASSWORD. THE MAIN MENU OPTIONS ARE DISPLAYED. Press ENTER begin. to Please enter your password to access the Management Functions. Status: IDLE ENTER MAIN MENU 1. 1. 2. 3. 4. 2. TRIAL CLOSE DAY CLOSE TRIAL CASSETTE CLOSE CASSETTE CLOSE DIAGNOSTICS 1. 2. 3.
CASSETTE CLOSE FUNCTIONS (REAR OPERATOR PANEL - TOUCHSCREEN) PRESS TO START. CLOSE CASSETTE( S) - TOUCH CASSETTE OPTIONS ON TOUCHPAD UNTIL “ASTERICK” APPEARS. SELECT “CONTINUE”. Select the cassettes to close. WARNING: Cassette totals will be reset for the selected cassettes ENTER PASSWORD. * Cassette A: $10.00 * Cassette B: $20.00 Continue PLACE CASSETTES “IN-SERVICE”. TOUCH CASSETTE OPTIONS ON TOUCHPAD UNTIL “A STERICK ” AP PEARS. S ELECT “C ONTINUE”.
REPLENISH NMD-100 CASSETTE(S) STEP ACTION STEP 1 UNLOCK/OPEN DISPENSER SECURITY DOOR. GRASP CASSETTE HANDLE WITH ONE HAND WHILE HOLDING MECHANISM WITH THE OTHER. PULL CASSETTE OUT SLIGHTLY, THEN PLACE ONE HAND UNDERNEATH. REMOVE CASSETTE. 5 CASSETTE AND LEVEL NOTE HOLD THE NOTES. EXTEND THE “PAWLS” ON PACKER PLATE FULLY. CLOSE LID AND INSTALL IN DISPENSER. PLACE CASSETTE ON A LEVEL SURFACE. INSERT CASSETTE KEY INTO THE CASSETTE LOCK AND TURN “CLOCKWISE”. PRESS “GREEN” RELEASE BUTTON TO RAISE LID.
REPLENISH RECEIPT PAPER NOTE: THIS PROCEDURE REQUIRES TERMINAL IS POWERED UP. STEP 1 ACTION OPEN THE 4 REAR SLEEVE CABINET DOOR . STEP IF PAPER RE - MAINS ON ROLL, CUT ACTION I NSTALL NEW PAPER ROLL/ SPINDLE IN BRACKET. PAPER FEEDS FROM TOP OF ROLL! OR TEAR PAPER BE TWEEN ROLL AND PRINTER . REMOVE PER SPENT PA - ROLL AND SPINDLE FROM PAPER BRACKET. 2 PULL 5 RELEASE HANDLE UP AND RO- TATE PRINTER ASSEMBLY DOWN. FEED END OF PAPER INTO PRINTER TAKEUP SLOT .
COMMON ERROR CODES ERROR CODE MEANING RECOMMENDATIONS 1. REMOVE AND OPEN CASSETTE(S). IF THERE IS CURRENCY IN CASSETTE, GO IF NOT, LOAD CURRENCY AND PROCEED TO STEP 3. TO STEP 2. 302 FEED FAILURE 306 2. IS CURRENCY OF GOOD QUALITY? IF YES, GO TO STEP 4. IF NOT, OBTAIN PROCEED TO STEP 4. QUALITY CURRENCY. 3. SHUFFLE CURRENCY AND REPACK CASSETTE. 4. RE-INSERT CASSETTE USING REPLENISHING CASSETTE PROCEDURES. 5. PERFORM A TEST DISPENSE (DIAGNOSTICS>DISPENSER>TEST DISPENSE).
COMBINATION LOCKS INTRODUCTION THE SECURITY CABINET CAN BE SECURED USING AN ELECTRONIC COMBINATION LOCK. THESE PAGES COVER HOW TO OPERATE THE COMBINATION OF EITHER ELECTRONIC LOCK OFFERED. OPERATING THE ELECTRONIC LOCK THE ELECTRONIC LOCK COMBINATION CONSISTS OF SIX DIGITS. UPON ARRIVAL, THE COMBINATION OF THE LOCK SHOULD ALREADY BE PRESET TO 1-2-3-4-5-6. NOTE: CHANGE THIS COMBINATION! SEE USER MANUAL FOR CHANGING COMBINATIONS PROCEDURES. ENTERING THE COMBINATION 1.
