Owner Manual

ManualsBrandsTriton Systems ManualsOtherTDM

TDM ENHANCEMENT KIT

INSTALLATION PROCEDURES

VERSION 1.0

TDN 07100-00030 11/2003

CORPORATE HEADQUARTERS: RMA (RETURN MATERIAL AUTHORIZATION)

RETURN ADDRESS:

522 E. Railroad Street 21405 B Street

Long Beach, MS 39560 Long Beach, MS 39560

PHONE: (228) 868-1317

FAX: (228) 868-0437

publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or

translated into any human or computer language, in any form, by any means whatsoever,

without the express written permission of Triton Systems of Delaware, Inc. DOVER

and the DOVER logo are registered trademarks of Delaware Capital Formation, Inc., a

wholly-owned subsidiary of Dover Corporation.

Summary of content (7 pages)

PAGE 1
TDM ENHANCEMENT KIT INSTALLATION PROCEDURES VERSION 1.0 TDN 07100-00030 11/2003 CORPORATE HEADQUARTERS: RMA (RETURN MATERIAL AUTHORIZATION) RETURN ADDRESS: 522 E. Railroad Street Long Beach, MS 39560 PHONE: (228) 868-1317 FAX: (228) 868-0437 21405 B Street Long Beach, MS 39560 COPYRIGHT NOTICE Copyright © Delaware Capital Formation, Inc., 2003. All rights reserved.
PAGE 2
TDM ENHANCEMENT KIT INSTALLATION PROCEDURES Introduction The following describes how to install the protective plastic cover for the TDM dispensing mechanism and associated hardware for 9100, 9705, and RL5000 (w/ TDM mechanism) ATMs. PARTS AND TOOLS REQUIRED TOOLS R EQUIR ED #1 Phillips Screwdriver Torx Driver T- 6 (6mm) Torx Driver T- 10 (10mm) TD M EN HAN CEM EN T KIT P/N 06200-00075 PARTS SUPPLIED PART N UM BER D ESCR IPTION QUAN TITY 03072- 00015 EMI Shield, Plastic 1 02054- 00087 Screw, M2.
PAGE 3
TDM ENHANCEMENT KIT INSTALLATION PROCEDURES 4. Remove the currency and reject cassette. Using a #1 Phillips screwdriver, remove the 4 screws located in the bottom of the note cassette opening. (Figure 3) Remove the dispenser from the tray. 5. Place the dispenser on a flat, level surface. Using a T-10 Torx driver, remove the ground wire from the motor housing (Figure 4) and relocate to the screw below the motor gear shown in Figure 5. 6. Fig. 3. Screw locations.
PAGE 4
TDM ENHANCEMENT KIT INSTALLATION PROCEDURES 11. Reinstall the dispenser on the tray and secure with the 4 screws. Route the power and data cables through the tie wrap loop and connect to the dispenser board. (Figure 11) Tie wrap openings 11. Pull the tie wrap taut until the cables are secured in place. (Figure 12) Fig. 7. Feed tie wrap. 12. Install the note and reject cassette. Rotate the dispenser 180° counterclockwise back to the operate position. Installation of the Enhancement kit is complete.
PAGE 5
TDM ENHANCEMENT KIT INSTALLATION PROCEDURES Installing the TDM Enhancement kit for Models 9705/RL5000 ATMs Follow these steps to install/secure the protective plastic cover, cable clip, and power/data cables to the dispenser.. 1. Open the control panel hood. Turn the power switch on the power supply to the OFF (0) position. 2. Open the dispenser vault door. Slide the dispenser tray out to its fully extended position. (Figure 1) 3.
PAGE 6
TDM ENHANCEMENT KIT INSTALLATION PROCEDURES 8. Feed the tie wrap provided through either openings located near the data cable connector.as shown in Figure 6. Start the tie wrap slightly but Do Not pull tight. (Figure 7) 9. Install a Flat wire clip on the underside of the vault ceiling. To gauge where to affix the clip, slide the dispenser fully into the cabinet. Notice the location of the presenter motor (Figure 7). Clip will be installed on the ceiling above where motor is located.
PAGE 7
TDM ENHANCEMENT KIT INSTALLATION PROCEDURES 10. Route the power and data cable through the clip and snap in place. (Figure 8) 11. Route the power and data cables through the tie wrap loop and connect to the dispenser board. (Figure 9) 12. Pull the tie wrap taut until the cables are secured in place. (Figure 10) Fig. 9. Route cables through tie wrap and connect to dispenser.. 13. Rotate the dispenser 180° counterclockwise back to the operate position. Installation of the Enhancement kit is complete.