Model RL2000 QUICK REFERENCE GUIDE THIS AREA FOR SERVICE PROVIDER CONTACT INFORMATION: TDN 07103-00158B Jan 2009
MANAGEMENT FUNCTIONS - ACCESS INSTRUCTIONS 1. 2. AT ATM WELCOME SCREEN, PRESS AND HOLD DOWN THE KEY (LOWER - RIGHT CORNER OF KEYPAD ), PRESS <1> KEY , THEN RE LEASE BOTH KEYS. THE TOP MENU WILL BE DISPLAYED . AT THE TOP MENU, SELECT MANAGEMENT FUNCTIONS OPTION. ENTER . THE MANAGEMENT FUNCTIONS MAIN MENU IS DISPLAYED. PASSWORD AND SELECT RESTART / SHUTDOWN TERMINAL FOLLOW ACCESS INSTRUCTIONS TO ENTER MANAGEMENT FUNCTIONS. SE- LECT SYSTEM PARAMETERS.
CLOSE FUNCTIONS FOLLOW ACCESS INSTRUCTIONS TO ENTER MANAGEMENT FUNCTIONS. S ELECT TERMINAL CLOSE FUNCTIONS. DAY CLOSE: THIS OPTION IS USED TO COMPLETE DAILY BALANCING OF THE ATM WITH THE PROCESSOR. TOTALS ARE CLEARED AND SWITCHED TO THE NEXT BUSINESS DAY. TRIAL CLOSE: THIS OPTION FUNCTIONS LIKE A DAY CLOSE EXCEPT THE TOTALS ARE NOT CLEARED. JOURNAL FUNCTIONS FOLLOW ACCESS INSTRUCTIONS TO ENTER MANAGEMENT FUNCTIONS. S ELECT JOURNAL.
CASSETTE CLOSE FUNCTIONS FOLLOW ACCESS INSTRUCTIONS TO ENTER MANAGEMENT FUNCTIONS. SELECT TERMINAL CLOSE FUNCTIONS. SELECT CASSETTE CLOSE. SELECT CASSETTE(S) TO CLOSE. A CHECK MARK (√ √ ) IDENPRESS . TIFIES WHICH CASSETTE(S) ARE SELECTED. AFTER CASSETTE(S) HAVE BEEN REINSERTED IN THE DISPENSER, . PRESS NOTE: IF AN NMD-50 DISPENSER IS INSTALLED, WAIT FOR THE CASSETTES TO LOCK ( THIS IS DONE AUTOMATICALLY ). PRESS IF APPLICABLE.
REPLENISH TDM CASSETTE(S) (TDM-250) STEP 1 ACTION UNLOCK/OPEN DISPENSER SECURITY DOOR. RELEASE THE SLIDE LOCKING LEVER AND EXTEND THE DISPENSER ACTION STEP MOUNTING TRAY FULLY. 4 R EMOVE THE N O T E CASSETTE(S). UNLOCK AND MOVE PACKER PLATE TO REAR OF THE CASSETTE . LATCH IN PLACE WITH THE HOLD-BACK LATCH. 2 L OCATE THE S P R I N G - LOADED LOCKING PIN ON UNDERSIDE OF TRAY. PULL PIN DOWN AND ROTATE 180° RELEASE PIN TO LOCK IN PLACE. SWIVEL PLATFORM Note cassettes CLOCKWISE.
REPLENISH SDD CASSETTE STEP 1 ACTION UNLOCK/OPEN DISPENSER SECURITY DOOR. G RASP THE CASSETTE HANDLE AND REMOVE THE CASSETTE. ACTION STEP 4 LIFT THE REJECT TRAY. PUSH THE PACKER PLATE TO REAR OF CASSETTE AND LATCH IN PLACE. CASSETTE MUST BE PRIMEDWITH THE CASSETTE 2 KEY BEFORE INSERTING ON O THE LOADING TRAY. INSERT KEY AND TURN CLOCKWISE TO SHOW INDICATOR IN WINDOW. GREEN 5 Green window COUNT THE NUMBER OF BILLS THAT REMAIN IN THE CASSETTE, IF ANY.
REPLENISH MINIMECH CASSETTE STEP ACTION 1 UNLOCK/OPEN DISPENSER SECURITY DOOR. G RASP TRAY HANDLE AND REMOVE NOTE CASSETTE 2 3 4 STEP ACTION 5 PLACE CURRENCY IN THE CASSETTE. SLOWLY PUSH PACKER FORWARDS AGAINST THE NOTES. 6 GRASP THE HANDLE AND SLIDE THE NOTE CASSETTE FULLY INTO THE DISPENSER. REMOVE ANY REJECTED NOTES FROM THE REJECT COMPARTMENT. DO NOTRECYCLE REJECTED NOTES! MOVE THE PUSHER PLATE TO THE REAR OF THE TRAY (TOWARDS THE HANDLE).
REPLENISH NMD-50 CASSETTE(S) STEP ACTION 1 UNLOCK/OPEN DISPENSER SECURITY DOOR. GRASP CASSETTE HANDLE WITH ONE HAND WHILE HOLDING MECHANISM WITH THE OTHER. PULL CASSETTE OUT SLIGHTLY, THEN PLACE ONE HAND UNDER - NEATH. SETTE. REMOVE CAS- ACTION STEP 5 PLACE CURRENCY IN THE CASSE T T E AND MOVE PACKER PLATE AGAINST THE 2 3 NOTES. PRESS THE GREEN RELEASE BUTTON AND LIFT THE LID. FLIP THE LID BACK FULLY LETTING IT REST ON A FLAT SURFACE. 6 EXTEND THE “PAWLS” ON PACKER PLATE FULLY .
REPLENISH RECEIPT PAPER NOTE: THIS PROCEDURE REQUIRES TERMINAL IS POWERED UP. STEP 1 ACTION STEP OPEN CONTROL PANEL. IF PAPER REMAINS ON 4 INSTALL NEW PAPER ROLL ONTO SPINDLE. ROLL , CUT OR TEAR PAPER BETWEEN ROLL AND ACTION PRINTER . 2 PRESS THE MANUAL FEED BUTTON TO CLEAR 5 INSERT PAPER/SPINDLE INTO PAPER BRACKET. PAPER FEEDS FROM TOP OF ROLL! 3 REMOVE SPENT PAPER ROLL AND SPINDLE FROM PAPER BRACKET. 6 FEED END OF PAPER INTO PRINTER TAKE-UP SLOT.
COMBINATION LOCKS INTRODUCTION THE SECURITY CABINET CAN BE SECURED USING EITHER A MECHANICAL OR ELECTRONIC COMBINATION LOCK. THIS PAGE COVERS HOW TO OPERATE THE COMBINATION OF EITHER LOCK. OPERATING THE MECHANICAL LOCK UNLOCKING THE LOCK THERE ARE TWO MARKS ON THE DIAL RING. THE INDEX AT THE TOP IS USED FOR OPENING THE LOCK, THE INDEX 30 DEGREES TO THE LEFT IS USED ONLY WHEN CHANGING THE COMBINATION. THE DIAL SHOULD ALWAYS BE TURNED SLOWLY AND EVENLY.
