Owner Manual

ManualsBrandsTriton Systems ManualsOtherMako/SS

MAKO

EXTENDED CABINET

INSTALLATION GUIDE

VERSION 2.0

TDN 07102-00033 03/01

reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any hu-

man or computer language, in any form, by any means whatsoever, without the express

written permission of Triton Systems, Inc.

MAKO is a registered trademark of Triton Systems, Inc.

CORPORATE HEADQUARTERS: RMA (RETURN MATERIAL AUTHORIZATION)

RETURN ADDRESS:

522 E. Railroad Street 21405 B Street

Long Beach, MS 39560 Long Beach, MS 39560

PHONE: (228) 868-1317

FAX: (228) 868-0437

Summary of content (7 pages)

PAGE 1
MAKO® EC EXTENDED CABINET INSTALLATION GUIDE VERSION 2.0 TDN 07102-00033 03/01 CORPORATE HEADQUARTERS: RMA (RETURN MATERIAL AUTHORIZATION) RETURN ADDRESS: 522 E. Railroad Street Long Beach, MS 39560 PHONE: (228) 868-1317 FAX: (228) 868-0437 21405 B Street Long Beach, MS 39560 COPYRIGHT NOTICE Copyright © 2001 Triton Systems , Inc. All rights reserved.
PAGE 2
MAKO EC EXTENDED CABINET INSTALLATION GUIDE PARTS SUPPLIED 4 3/4" Expansion Anchors 4 Flat Washers 4 3/8"-16 x 1.75, Hex Bolts 4 Lock Washers 1 Drill Template, Part Number 03075-10001 REQUIRED TOOLS/EQUIPMENT 1 Heavy-Duty Electric Hammer Drill 1 Safety Goggles 1 Back-Support Belt 1 9/16" Socket 1 1/4", 3/4" Drill Bits ea. 1 Ear Plugs or Muffs (hearing protection) 1 Portable Vacuum Cleaner A torque w rench (capable of 30 foot-pounds) is required to tighten the cabinet mounting bolts.
PAGE 3
MAKO EC EXTENDED CABINET INSTALLATION GUIDE UNPACK CASH DISPENSER Retaining Screws **IMPORTANT** The Cash Dispenser is designed for indoor installation only! 1. Carefully inspect the unit for any shipping damage and report any damage immediately to the shipping company. Refer to the Warranty Information in the operation or service manual (as applicable) for information about reporting shipping damage. Fig. 1. Floor-Plate In Place. 2.
PAGE 4
MAKO EC EXTENDED CABINET INSTALLATION GUIDE MARK/DRILL MOUNTING HOLES CONCRETE STRENGTH The floor at the installation location should consist of commercial-grade concrete, measuring at least 3000 psi in compression strength. The full effectiveness of the anchor bolts depends upon meeting this specification! Check with the contractor/builder or owner of the installation to verify that this requirement can be satisfied.
PAGE 5
MAKO EC EXTENDED CABINET INSTALLATION GUIDE 2. Use a 1/4-inch diameter carbide-tipped masonry bit to drill four pilot holes at the drilling points marked in the previous step. Drill the pilot holes approximately 1/2-inch deep into the floor. See Figure 6. These holes will help guide the 3/4-inch masonry bit that will be used to drill the anchor-bolt holes in the next step. 3. Use a 3/4-inch diameter carbide-tipped masonry bit to drill four holes at least 1 3/4 inches deep into the floor. See Figure 7.
PAGE 6
MAKO EC EXTENDED CABINET INSTALLATION GUIDE 3. Move the pedestal back into position for mounting. Align the mounting-hole cutouts in the pedestal base with the mounting holes. 4. Insert a 3/8-inch security bolt through a provided lock washer, flat washer and into each insert. Attach a 9/16-inch socket to a torque wrench and tighten each bolt to a setting of 30 footpounds.
PAGE 7
MAKO EC EXTENDED CABINET INSTALLATION GUIDE Fig. 11. Mounting Hole Drill Template Example (Not to Scale). TRITON SYSTEMS, INC.