MODEL 9200 (SUPERSCRIP™) INSTALLATION GUIDE VERSION 1.0 TDN 07100-00028 09/2003 CORPORATE HEADQUARTERS: 522 E. Railroad Street Long Beach, MS 39560 PHONE: (228) 868-1317 FAX: (228) 868-0437 RMA (RETURN MATERIAL AUTHORIZATION) RETURN ADDRESS: 21405 B Street Long Beach, MS 39560 COPYRIGHT NOTICE Copyright © Delaware Capital Formation, Inc., 2001, 2003. All rights reserved.
MODEL 9200 (SUPERSCRIP) INSTALLATION GUIDE USE OFTHIS PRODUCT INAMANNER OTHER THAN THOSE DESCRIBED IN THIS MANUAL MAY RESULT IN PERSONAL INJURY. USA TELECOM: Statement of Compliance: This equipment complies with Part 68 of the FCC rules. Located in the control area of the terminal is the product label. This label lists the FCC registration number and ringer equivalence number of the unit. If requested, this information must be provided to the telephone company.
MODEL 9200 (SUPERSCRIP) INSTALLATION GUIDE If the equipment is causing harm to the network, the telephone company may request that you disconnect the equipment until the problem is resolved. Repairs should be made only by qualified factory representatives. Party Lines: The 9200 SuperScrip must not be used on party lines. Alarm Equipment: The 9200 SuperScrip should have its own dedicated phone line. Do not install the 9200 on the same line as alarm equipment.
MODEL 9200 (SUPERSCRIP) INSTALLATION GUIDE AVIS: L’étiquette d’Industrie Canada identific le matériel homologué. Cette étiquette certifie que le matériel est conforme aux normes de protection, d’exploitation et de sécurité des réseaux de télécommunications, comme le prescrivent les documents concernant les exigences techniques relatives au matériel terminal. Le Ministère n’assure toutefois pas que le matériel fonctionnera à la satisfaction de l’utilisateur.
MODEL 9200 (SUPERSCRIP) INSTALLATION GUIDE Party Lines: The Model 9200 series cash dispenser must not be used on party lines. Alarm Equipment: The Model 9200 series cash dispenser should have its own dedicated phone line. Do not install the 9200 on the same line as alarm equipment. Electrical Safety Advisory: Telephone companies report that electrical surges, typically lightening transients, are very destructive to customer equipment connected to AC power sources.
MODEL 9200 (SUPERSCRIP) INSTALLATION GUIDE What’s in This Installation Guide This Installation Guide gives step-by-step procedures for completing the physical installation of a Model 9200 SuperScrip. This guide covers pedestal, table-top, and signage installation for a 9200 terminal. The Installation Guide is divided into the following sections: **Notice** Equipment is to be installed by trained personnel, in accordance with the installtion instructions provided with each unit.
ATM INSTALLATION FOR ACCESSIBILITY 7
MODEL 9200 (SUPERSCRIP) INSTALLATION GUIDE 4.34 Automated Teller Machines. ATM INSTALLATION FOR ACCESSIBILITY 4.34.1 General. Each machine required to be accessible by 4.1.3 shall be on an accessible route and shall comply with 4.3.4. 1. This document supercedes all other information provided by Triton for ATM installation for accessibility. 2.
ATM INSTALLATION FOR ACCESSIBILITY (b) Reach Depth More Than 10 inches (255 mm).
MODEL 9200 (SUPERSCRIP) INSTALLATION GUIDE 4.2.4.2 Relationship of Maneuvering Clearance to Wheelchair Spaces. One full unobstructed side of the clear floor or ground space for a wheelchair shall adjoin or overlap an accessible route or adjoin another wheelchair clear floor space. If a clear floor space is located in an alcove or otherwise confined on all or part of three sides, additional maneuvering clearances shall be provided as shown in Fig. 4(d) and 4(e). Figure 4a. Clear floor space. 4.2.4.
ATM INSTALLATION FOR ACCESSIBILITY Figures 4d. Clear floor space in alcoves. Figures 4e. Clear floor space in alcove. For a front approach, where the depth of the alcove is equal to or less than 24 inches (610 mm), the required clear floor space is 30 inches by 48 inches (760 mm by 1220 mm). For a front approach, if the depth of the alcove is greater than 24 inches (610 mm), then in addition to the 30-inch (760 mm) width, a maneuvering clearance of 6 inches (150 mm) in width is required.
MODEL 9200 (SUPERSCRIP) INSTALLATION GUIDE Figure 5a. Forward reach, unobstructed. Figure 5b. Forward reach, obstructed.
ATM INSTALLATION FOR ACCESSIBILITY Figure 6b. Parallel approach - high/ low side reach. Figure 6a. Parallel approach - side reach. Figure 6c. Side reach, obstructed.
THIS PAGE INTENTIONALLY LEFT BLANK 14
ENVIRONMENTAL PRECAUTIONS CHECKLIST 15
ENVIRONMENTAL PRECAUTIONS CHECKLIST When installing a SuperScrip terminal, some general environmental precautions need to be considered. We have discovered that there are some devices that may interfere with the performance of the unit. Evaluate the location where the terminal will be installed. To help ensure proper operation of the unit, ensure the environmental criteria listed in this checklist are met. TEMPERATURE/HUMIDITY 1.
INSTALLATION PROCEDURES (KIOSK, TABLE-TOP, SIGNAGE) 17
MODEL 9200 (SUPERSCRIP) INSTALLATION GUIDE KIOSK INSTALLATION PROCEDURES SUGGESTED MOUNTING HARDWARE 4 3/8" Expansion Bolt (at least two inches long) 4 3/8" flat washer ELECTRICAL/MECHANICAL SAFETY Observe ALL safety precautions for electrical equipment.
KIOSK INSTALLATION PROCEDURES 3. Fig. 3a Fig. 3b Fig. 3c Fig. 3d Mark the drilling points. Locate the four (4) hole cut-outs in the metal floor of the pedestal base. Use them to mark the drilling points for the pedestal mounting holes. (Figure 4) Preferred Method. Place the included mounting hole drill template on the floor in the designated location and tape it into position.
MODEL 9200 (SUPERSCRIP) INSTALLATION GUIDE Use a center punch tool (or equivalent) to mark the center of each mounting hole, as indicated on the template. Use a felttip pen or other marker to carefully mark the front corners of the cabinet. These marks will serve as guides to align the cabinet in the final mounting position. Remove the template. Figure 5 provides an example (not to scale) of the template. Alternative Method. Move the pedestal to the location where it will be installed.
KIOSK INSTALLATION PROCEDURES 6. Route phone/power cables. Locate the unit’s phone and power cables in the pedestal enclosure and route the cables through the cutout in the lower rear corner of the cabinet (see Figure 4). 7. Install the lower sign panel and secure in place using the securing plate, as shown in Figures 7a through 7d. Apply pressure to the screws in the plate to lock it into position. Fig.
MODEL 9200 (SUPERSCRIP) INSTALLATION GUIDE TABLE INSTALLATION PROCEDURES SU GGESTED MOU N TIN G H AR D WAR E 4 TOOL USE/SAFETY Observe ALL safety precautions for operating hand and power tools! Wear eye protection while operating the electric drill and while using the hammer to drive anchor spikes into the floor! 1/4-20 Hex Bolts (Length depends upon countertop thi ckness) 8 1/4" ID (Inner D i ameter) Flat Washers 4 1/4" ID Lock Washers 4 1/4"-20 Hex Nuts 1 3/8" D ri ll Bi t R EQU IR ED TOOLS/EQ
TABLE-TOP INSTALLATION PROCEDURES 3. Use the center punch (or equivalent) to mark the drilling points as indicated on the template. Remove the template. (Figure 4) 4. Drill the four mounting holes at the locations marked in Step 3, using the 3/8” drill bit and electric drill. (Figure 5) 5. Place the SuperScrip on the mounting surface. Perform the following steps: • Open the unit using the enclosure security key, Locate the power and telephone cables. Uncoil these cables.
MODEL 9200 (SUPERSCRIP) INSTALLATION GUIDE OPTIONAL STEPS (7-9) At this point, the SuperScrip unit has been secured on the right side. This may be sufficient for your application. If so, you can skip Steps 7-9, which involve removing the power supply in order to access the mounting holes on the left side of the unit. Go directly to Step 10, which concludes the installation procedure by closing, locking and placing the unit in service. Fig. 8 7.
TABLE-TOP INSTALLATION PROCEDURES 8. Using two, 1/4” bolts, secure the SuperScrip using the two remaining mounting holes on the bottom lefthand side of the unit. • Place one flat washer under the head of each bolt and place the bolt through the mounting hole. The head of the bolt will be inside the unit. (Figure 14) From underneath the mounting surface, place a flat washer, then a lock washer and finally a nut on each bolt. Tighten down with the 7/16” socket and ratchet wrench. (Figure 9) • 9.
MODEL 9200 (SUPERSCRIP) INSTALLATION GUIDE PAR TS PR OVID ED R EQU IR ED TOOLS 1 Adverti si ng Si gn 1 #2 Phi lli ps Screwdri ver 2 Plasti c Thread-C utti ng Screw, Phi lli ps Head, 4 mm di a. by 12 mm long. Follow these steps to install the Advertising sign for the SuperScrip unit: 1. 2. Locate the advertising sign mounting holes on the rear of the top enclosure, as shown in Figures 1. If necessary, move the unit to provide access to the mounting holes.
