Owner Manual

ManualsBrandsTriton Systems ManualsOtherFT5000 Xscale Series

BALLAST/BULB TO LED

FIELD CONVERSION GUIDE

(FOR FT5000 X-SCALE LIGHT PANEL)

CORPORATE HEADQUARTERS: RMA (RETURN MATERIAL AUTHORIZATION)

RETURN ADDRESS:

522 E. Railroad Street 21405 Avenue “B”

Long Beach, MS 39560 Long Beach, MS 39560

Phone: (228) 868-1317

Fax: (228) 868-0437

VERSION 1.0

TDN 07100-00066 09/2006

of Delaware, Inc. is an operating company of Dover Electronics, Inc., a subsidiary

of Dover Corporation (NYSE-DOV). DOVER, the DOVER logo and the Dover

family of marks and TRITON, the TRITON logo and the Triton family of marks

are registered trademarks of Delaware Capital Formation, Inc., a wholly owned

subsidiary of Dover Corporation.

Summary of content (8 pages)

PAGE 1
BALLAST/BULB TO LED FIELD CONVERSION GUIDE (FOR FT5000 X-SCALE LIGHT PANEL) VERSION 1.0 TDN 07100-00066 09/2006 CORPORATE HEADQUARTERS: RMA (RETURN MATERIAL AUTHORIZATION) RETURN ADDRESS: 522 E. Railroad Street Long Beach, MS 39560 Phone: (228) 868-1317 Fax: (228) 868-0437 21405 Avenue “B” Long Beach, MS 39560 COPYRIGHT NOTICE © 2006 Delaware Capital Formation, Inc. All Rights Reserved. Triton Systems of Delaware, Inc. is an operating company of Dover Electronics, Inc.
PAGE 2
BALLAST /BULB TO LED CONVERSION (FT5000) IMPORTANT NOTICE Triton Systems has discontinued offering a ballast/bulb (AC-powered) light assembly for topper signage (mid/high) and light panels. This affects models 8100, 9100, 97XX, RL5000 (X-Scale/XP), and FT5000 (X-Scale) units. LED-lit (DC-powered) light assemblies will be the replacement option. Note: Limited ballast/bulb parts may be available for field replaceable parts and repair until current inventory is depleted.
PAGE 3
BALLAST/BULB TO LED CONVERSION (FT5000) SCOPE This procedure applies to all service personnel involved in the process of maintaining or converting Triton ATMs.
PAGE 4
BALLAST /BULB TO LED CONVERSION (FT5000) FT5000 LIGHT PANEL LED CONVERSION PROCEDURE Note: These procedures are completed with the terminal AC power OFF. If terminal is ON, enter MANAGEMENT FUNCTIONS > SYSTEM PARAMETERS > SHUT DOWN THE TERMINAL. When prompted, turn power OFF on the units power supply. Â REMOVING BALLAST/BULB LIGHT PANEL: 1. Unlock and open the cabinet sleeve door. Grasp handle on printer assembly, lift up, and pivot assembly down. This will allow better access to light panel removal.
PAGE 5
BALLAST/BULB TO LED CONVERSION (FT5000) Â ASSEMBLE LED LIGHT BAR/BRACKET/CABLE: 1. Mount the LED light bar (P/N 09100-00188) to the bracket (P/N 03011-00789) as shown in figure below. Secure with the three (3) screws/nuts provided using a phillips screwdriver and box wrench. 2. Plug the 2-pin connector end of the LED power cable (P/N 09120-00332) to J5 on the LED light bar module as shown below. Â 1.
PAGE 6
BALLAST /BULB TO LED CONVERSION (FT5000) 2. Â Install the LED light panel assembly as shown below with the three (3) screws removed from the previous step. CABLE ROUTING AND CONNECTIVITY: 1. Route the LED power cable (and speaker wires) through the slot shown below. If a grommet was previously in place, route cables through the grommet and insert grommet in the slot. 2. Connect the 8-pin molex connector of the LED power cable to any unused connector of the power supply.
PAGE 7
BALLAST/BULB TO LED CONVERSION (FT5000) Units that have power supplies where all 8-pin connectors are in use: Remove one (1) of the cables (preferably any that has two (2) wires connected) from the power supply. Using the power splitter cable included (P/N 0912000826), connect the LED power cable to one side and the recently removed cable to the other. Plug the female end of the splitter to an 8-pin molex connector on the power supply. power splitter cable 3.
PAGE 8
BALLAST /BULB TO LED CONVERSION (FT5000) THIS PAGE INTENTIONALLY LEFT BLANK 8