Manual

78 79
Instructions for use TRISA Hard Floor Cleaner Instructions for use TRISA Hard Floor Cleaner
7.3 Emptying the waste water tank and catch bucket
The hard oor cleaner’s waste water system consists of a HEPA lter, lter holder, catch bucket and waste water
tank. Clean the catch bucket and waste water tank after each use.
To empty the waste water tank and catch bucket:
1. Press the power button Ⓑ to switch the hard oor cleaner o.
2. Remove the waste water tank Ⓧ by pressing the waste release button Ⓘ. ⓭
3. Disassemble the waste water tank Ⓧ, catch bucket Ⓦ, filter holder Ⓥ and
HEPA filter Ⓤ. ⓮
NOTICE! Make sure the HEPA lter stays dry.
4. Empty the waste water tank Ⓧ and catch bucket Ⓦ.
5. Clean and dry the waste water tank Ⓧ and catch bucket Ⓦ. ⓮
6. Assemble the waste water tank Ⓧ, catch bucket Ⓦ, filter holder Ⓥ and HEPA filter Ⓤ again.
7. Put the waste water tank Ⓧ back into the hard oor cleaner. ⓯
7.4 Cleaning the HEPA lter
The hard oor cleaner has a HEPA lter containing a sponge. Clean the sponge after each use. Replace the HEPA
lter every 6-12 months.
1. Press the power button Ⓑ to switch the hard oor cleaner o.
2. Remove the waste water tank Ⓧ by pressing the waste release button Ⓘ.
3. Remove the HEPA filter Ⓤ.
4. Open the HEPA filter Ⓤ and remove the sponge Ⓣ. ⓰
5. Shake any dirt o the sponge Ⓣ, or wash the sponge Ⓣ with water.
WARNING! Make sure the sponge is completely dry and clean before putting it back in the
lter.
6. Shake the dust out of the HEPA filter Ⓤ.
7. Put the sponge Ⓣ back in the HEPA filter Ⓤ, and put the HEPA filter Ⓤ back in the hard oor
cleaner.
7 Using the hard oor cleaner
7.1 Filling the water tank
1. Twist the water tank Ⓗ counterclockwise. ➑
2. Pull the water tank Ⓗ o the hard oor cleaner.
3. Open the cap of the water tank Ⓗ.
4. Fill the water tank Ⓗ with water up to the MAX line. ➒
NOTICE! To avoid damaging the hard oor cleaner, make sure the water is not more than
40°C.
5. If necessary, add a suitable non-foaming liquid detergent in a 1:20 ratio.
6. Close the water tank Ⓗ.
7. Push the water tank Ⓗ into the hard oor cleaner.
8. Twist the water tank Ⓗ clockwise. ➓
7.2 Cleaning the oor
1. Lift the hard oor cleaner o the charging stand Ⓡ.
2. Press the power button Ⓑ.
The hard oor cleaner is on and the brush roll Ⓞ starts spinning.
WARNING! Hold the handle tightly. The hard oor cleaner can move by itself if not held
tightly.
3. Select the Auto or Max intensity modes by pressing the mode button Ⓐ. ⓫
4. Make the oor wet by pushing the hard oor cleaner forward and pressing the
spray button Ⓓ. ⓬
5. Dry the oor by pulling the hard oor cleaner back.
In Auto mode, the hard oor cleaner senses the amount of dust and automatically adjusts the suction
accordingly. When the suction intensity is high, the display will show a red colour. When the suction intensity is
low, the display will show a blue colour.
In Max
mode, the maximum suction intensity is set.
The hard floor cleaner switches to standby mode when it is placed upright. To remove excess water, the brush
roll is spun out for 3 seconds. After 5 minutes of non-use, the device switches off.
Trisa_HardFloorCleaner - INDD - Second Draft.indd 78-79Trisa_HardFloorCleaner - INDD - Second Draft.indd 78-79 29-11-2022 01:04:4729-11-2022 01:04:47