Owner`s manual

ManualsBrandsTripp Lite Manualschassis componentsSR42UBZ4

SmartRack™ Enclosure

with Zone 4 Seismic Rating

Model: SR42UBZ4

Owner’s Manual

WARRANTY

REGISTRATION

chance to win a FREE Tripp Lite

product www.tripplite.com/warranty

1111 W. 35th Street, Chicago, IL 60609 USA

www.tripplite.com/support

Important Safety Instructions 2

Overview 2

Feature Identification 3

Enclosure Installation 4

Preparation 4

Unpacking 4

Placement 5

Ground Connection 5

Enclosure Configuration 6

Adding or Removing Front and Rear Doors 6

Reversing Front Door 6

Adding or Removing Roof Panel 8

Adding or Removing Side Panels 8

Adjusting Mounting Rails and Cable Management Rails 9

Equipment Installation 10

Installing or Removing Cage Nuts 10

Specifications 11

Storage and Service 11

Warranty and Warranty Registration 11

Español 12

Summary of content (11 pages)

PAGE 1
Y a e NT ION for Lit nty A R AT day Tripp arra R A TR to E /w W IS line FRE .com G on a te REster win ippli gi to .
PAGE 2
Important Safety Instructions SAVE THESE INSTRUCTIONS All sections of this manual contain instructions and warnings that should be followed during the installation and use of the SmartRack Enclosures described in this manual. Read all instructions and warnings thoroughly before attempting to move, install or use the SmartRack Enclosures described in this manual. Failure to comply will create a risk of personal injury and property damage and may affect the warranty.
PAGE 3
Feature Identification 2 1 3 4 6 6 3 7 5 8 1 Roof Panel 2 Locking Split Rear Doors 3 Locking Side Panels 4 Cable Management Rails 5 Zone 4 Seismic Brackets 6 Mounting Rails (Provide horizontal and vertical mounting points for equipment.) 7 Keys (One for the doors and one for the side panels.) 8 Locking Reversible Front Door Not Shown: Mounting hardware, documentation and other shipping materials.
PAGE 4
Enclosure Installation Caution! Read All Instructions and Warnings Before Installation! WARNING: The rack enclosure is extremely heavy. Do not attempt to unpack, move or install the enclosure without assistance. Until it has been properly installed and stabilized, the enclosure is prone to tipping and could cause property damage and/or personal injury. Use extreme caution when handling the enclosure and be sure to follow all handling and installation instructions.
PAGE 5
Enclosure Installation 4 Use the key to open the enclosure's doors and locate the base Zone 4 Seismic Brackets A and reinforcing brackets B that are bolted into the shipping pallet. Note: The keys are shipped in the accessory carton that comes attached to the side panel carton. B A 4 5 Use a 13 mm open-end wrench to remove the bolts attaching the enclosure to the shipping pallet. Be extremely careful, as the enclosure could shift unexpectedly after bolt removal.
PAGE 6
Enclosure Configuration Adding or Removing Front and Rear Doors WARNING: Do not attempt to add or remove doors without assistance. Removing Door 1 Disconnect the door's ground wire. 1 2 Open the door until it is perpendicular (90 degrees) to the front of the enclosure. 90° 2 3 Lift the door from the hinges and remove it from the enclosure.
PAGE 7
Enclosure Configuration 3 Remove the screw and washer from the rear of the door handle and remove the latching mechanism. Rotate the latch washer counter-clockwise 90 degrees and reverse the latch so it points in the opposite direction, then use the screw and washer to re-attach the latch to the rear of the door handle. 3 4 Remove the door by following the steps in the previous section.
PAGE 8
Enclosure Configuration Adding or Removing Roof Panel WARNING: Do not attempt to use the roof panel for weight-bearing purposes other than those explicitly described and approved by Tripp Lite. Do not attempt to add or remove the roof panel without assistance. Removing Roof Panel 1 Pull the 2 pins near the rear of the roof panel. While holding the pins, push the roof panel upward. 1 2 1 2 Remove the roof panel tabs A from the roof panel attachment slots B in the enclosure frame.
PAGE 9
Enclosure Configuration 3 Lift the panel away from the brace that supports it. To Reinstall Side Panel, Reverse Steps 1-3 3 Adjusting Mounting Rails and Cable Management Rails WARNING: Do not attempt to adjust rails without assistance. Do not attempt to adjust rails while equipment is installed in the enclosure. Do not attempt to use rails without screws installed (6 per rail). The 4 mounting rails are pre-installed to accommodate equipment with a mounting depth of 30 inches (762 mm).
PAGE 10
29 29 28 28 Equipment Installation WARNING: Do not install equipment until you have stabilized the enclosure. Install heavier equipment first and install it toward the bottom of the enclosure. Install equipment starting from the bottom of the enclosure and proceeding toward the top of the enclosure - never the reverse. If using sliding equipment rails, be careful when extending the rails. Do not extend more than one 27 27 set of sliding equipment rails at one time.
PAGE 11
Specifications Model SR42UBZ4 Load Rating Unit Dimensions Static Rolling Height Width Depth 3000 lb 2250 lb 78.5 in 23.