TRIPLETT CamView W35 Security Camera Wrist Monitor Instruction Manual 84-889 6-10 PDF compression, OCR, web optimization using a watermarked evaluation copy of CVISION PDFCompressor
• Thank you for purchasing the Triplett CamView W35 CCTV Monitor. Please read the complete manual carefully before using the product. • To assure safe use of this product, please read the section on Safety carefully, and observe any Cautions or Warnings posted there and throughout this manual. • Please keep this manual for future reference.
Table of Contents Safety Information ...............................................................................1 Introduction .........................................................................................2 Features ...............................................................................................3 Included Items .....................................................................................4 Controls and Indicators ..........................................................
1: Safety Information Dear Customer: For greatest safety and reliable operation, please follow these guidelines for use and care of the product. Please retain these instructions for future reference. 1. Do not expose the product to excessive dust or dirt, intense vibration, extreme humidity, or high temperatures. 2. If the product is damaged, there is a burnt smell, or smoke comes out of the case, immediately turn it off, take out the batteries, and unplug the charger.
8. Do not drop, strike, bend, or crush the batteries. Do not place the batteries in a metal container. Failure to observe this precaution may result in a chemical leak, fire, or explosion. 9. Use only the charger provided with the product. Use of a different charger may result in fire or explosion. 10. Do not exceed the input voltage rating of the charger (110~240 VAC / 50/60 Hz). 11. If battery leaks, avoid any contact with your eyes, skin, or clothing. If contact occurs, flush immediately with water.
16. Do not leave the product exposed to direct sunlight. 17. Do not allow children to use the product. 18. It is normal for the product to heat up while being used. 19. It is normal for the product to heat up while its batteries are charging. If possible, place the product in a ventilated area while the batteries are charging. 20. If the LCD screen is damaged, avoid contact with leaking fluid. Wash hands with soap and water. Flush eyes with water. 21.
2: Introduction The Triplett CamView W35 is a portable battery operated video monitor designed to aid CCTV and Security electronics installers and maintenance technicians. It’s high contrast 3.5” LCD screen provides a large image that is especially useful for adjusting camera setup, focus, and positioning, as well as viewing the video signal from DVR’s, DVD’s, VCR’s, or other video equipment.
3: Features • 3.
5: Controls and Indicators 1. Built-in 1 Watt speaker 2. Power / Charging Indicator, Bi-color LED (Red, Green) 3. MENU / Select Button 4. Increase Setting 5. Decrease Setting 6. MENU OFF 7. Charger Input (Power in) 8. Power Switch (OFF / ON) 9. Audio/Video Input (Camera in) 10. Audio/Video Output (AV out) 11. BNC Video Input 12. ¼ x 20 Mounting Thread Note: Refer to these identification numbers later in these instructions.
6: Battery Information To obtain the maximum battery life and avoid battery leaks, fire, or explosion, observe the following instructions and warnings. • Please charge the batteries before the first use of the product. • If the product is unused for several weeks, the batteries will slowly discharge by themselves. Recharge the batteries before use. • It is normal for batteries to heat up while charging or discharging. • Battery performance is reduced at low temperatures.
• Do not transport or store the batteries in a metal container or with other metal objects. • Do not throw batteries into a fire. They may explode. • Discard old batteries in an approved manner.
6: Installing and Charging the Batteries • Refer to the following figures to install the batteries. Flip the Stand up, pull it up, and twist it around out of the way of the battery cover. Remove the battery cover, sliding it in the direction of the arrow molded in the plastic . Install the batteries observing proper polarity. The flat end of the battery goes against the coil spring. Notice that the coil springs alternate on the side of the battery compartment.
Replace the battery cover and reposition the Stand so it fits into the cover. • Plug the charger into the power source (wall outlet) then plug the charger cable into the connector (7) on the side of the product. Observe Indicator LED(2). The LED should light up red and flash twice slowly (as the product tests the batteries) then turn on solidly to indicate the batteries are charging. If the LED begins to flash quickly, there is a problem with the batteries.
• Do not charge the batteries in a place where the temperature exceeds 140 degrees F. The batteries may be damaged or may explode. • Fully charged batteries will not charge again until they are depleted. Partially discharged batteries may be recharged at any time. • The charger is only rated for indoor use. • The product may be operated while the batteries are charging. In this case, the batteries will take longer to charge than if the product is turned off.
8: General Instructions Turning the Product On: After charging the batteries (see Section 7), slide switch (8) to its upper position to turn the product on. When operating from batteries, the LED should light up green. The CamView W35 continually tests for the presence and type of video signals applied to its input.
Connecting the Video and Audio Inputs: A video signal can be connected to the CamView W35 in two places. For the best durability, the BNC video input jack (11) should be used. The video input on the side of the W35 (9) uses a mini-plug and is more easily damaged that the BNC. However, if you need to put audio into the monitor, the side connector (9) will have to be used with the provided A/V cable.
On Screen Display (OSD) The factory settings are defaulted to “50”. When the settings are changed, the CamView W35 will remember them, even when the power is turned off. To select a specific setting to be altered, observe the location of the yellow cursor bar and press and release the MENU key (3) repeatedly until the bar highlights the desired setting. Then use the “ ”key (4) or “ ”key (5) to change the value of the setting as desired.
Using the Wristband: Refer to the following figures to attach and use the wristband. With the monitor face down, install the wristband through one slot as shown. The Velcro strips should be facing down. Put the end of the wristband through the other slot as shown. Pull the wristband completely through the slots until the metal buckle is against the first slot.
Front view of monitor and wristband Place monitor against wrist or arm with wristband hanging over arm. Bring end of wristband around back of arm and insert it through the buckle from the back, pulling it all the way through. Fold and pull end of wristband back over itself, adjusting to the desired tension, and secure against the Velcro strips.
Using the Stand as a Belt Clip: Refer to the following figures to use the Stand as a Belt Clip. Pull the stand out and let it hang loose. Slip the end of the Stand over belt or waist of pants.
Using the Stand: Refer to the following figures. Pull the stand out and let it hang loose. Pull Stand up (there is a spring inside) and rotate it by 90°. Release Prop monitor up using the Stand.
Using the Mounting Thread: Attach the monitor to a tripod or mounting bracket (not supplied) as shown in the following figures. Mounting bracket with ¼ x 20 thread. Screw the bracket into the female thread on the bottom of the monitor. Attach the bracket to wall or other surface.
Standby and Low Battery: When the battery is low, the LED (2) won’t light when the power switch (8) is turned on. There is a narrow region of battery voltage where the LED will light up green, but the monitor won’t operate. This can be mistaken for the Standby mode. To test to see if the monitor is in Standby or the battery is low, turn the power switch (8) off and back on. If the CVBS box appears, the monitor was in Standby.
9: Specifications Display 3.5” High Contrast Active Matrix TFT LCD Screen Video Formats Supported NTSC and PAL Resolution 320 x 240 Aspect ratio 4:3 Viewing Angle 40/60/60/60 (up/down/left/right) Brightness 250cd/m2 Contrast 350:1 Response time 25ms Video Level and Impedance 1.
Connectors Audio/Video Input (3.5mm, 4 circuit), Audio/ Video Output (2.5mm, 3 circuit), Charger Input (mini USB), Video Input (BNC) Battery Life 6 Hours continuous operation, (with full charge) 12 Hours Standby Batteries AA 1.2V 2500mAH NiMH x 4 AC Charger Input 110 ~ 240V-50/60Hz-0.30A Output DC 12V/1.5A Battery Recharge Time Approximately 1.
Product dimensions 4 ¾” x 3 ¾” x 1 ¼” Weight 9 Ounces Page 25 PDF compression, OCR, web optimization using a watermarked evaluation copy of CVISION PDFCompressor
10: Troubleshooting Problem Won’t turn on Monitor turns off Reason Solution Batteries discharged Charge battery Batteries installed incorrectly Install batteries correctly Bad battery connections Clean the battery terminals No video signal input Apply video signal to the input Charge battery Batteries discharged Video signal removed Battery is cold Short battery life Reapply video signal Warm monitor before using Bad battery connections Clean the battery terminals Battery has been charged
Problem Reason Solution Indicator LED is normal but battery doesn’t charge Bad battery connections Battery has been charged too many times Clean the battery terminals Replace with new batteries No video input Check video source and connections Replace cables No video display Bad cables Page 27 PDF compression, OCR, web optimization using a watermarked evaluation copy of CVISION PDFCompressor
11: Triplett One Year Limited Warranty Triplett warrants instruments and test equipment manufactured by it to be free from defective material or workmanship and agrees to repair or replace such products which, under normal use and service, disclose the defect to be the fault of our manufacturing, with no charge within one year of the date of original purchase for parts and labor. If we are unable to repair or replace the product, we will make a refund of the purchase price.
11: Triplett One Year Limited Warranty Cont. The purchaser agrees to assume all liability for any damages and bodily injury which may result from the use or misuse of the product by the purchaser, his employees, or others, and the remedies provided for in this warranty are expressly in lieu of any other liability Triplett may have, including incidental or consequential damages.
PDF compression, OCR, web optimization using a watermarked evaluation copy of CVISION PDFCompressor
