Quick Start Guide

Wally Sensors you have installed in your home to trigger the Shutoff Valve off. Users
may also manually trigger a shutoff via the Wally apps or by pressing the orange button
on the Shutoff Valve twice.
Shutoff Valve Specification
Dimensions 142x73x92mm (5.6x2.87x3.62)
Weight 640gr (1.41Lbs)
Power supply 4 x 3V batteries (CR123); removable compartment cover
Operation voltage 6V
Battery life span Up to five years, subject to the usage profile and valve use
frequency
Operating RF 2.4GHz
Transmission range Open space - up to 230 m (750 ft.). When a wall is within
the space - up to 120 m (390 ft.). To avoid poor wireless
communication, avoid installation within metal cabinets.
Compliant to FCC/IC
IP Rating IEC60529 IP68 – Dust and water tight and can be submerged
Working temperature -20 to +50ºC (-4 to +122ºF)
Actuator mounting pad ISO5211
Mounting Horizontal or perpendicular to the water main.
Thank you for choosing the Wally Shutoff Valve designed to work with the Wally
Starter Kit. Together they work to detect water leaks early and prevent additional
damage by shutting off the water supply. Wally protects your home and gives
you peace of mind.
Please Note
In order to take advantage of all the capabilities of the Shutoff Valve, you must pair it
with the Wally Hub from the Wally Starter Kit. Please read through the following
instructions carefully to ensure proper installation of the Shutoff Valve’s installation and
commissioning. If you have questions or run into issues during installation or operation,
please contact Wally at [e-mail].
• Warning! The product includes moving parts. Keep your fingers or othe objects away
from moving parts.
• Warning! This product was designed to prevent water leaks and as such should be
used for water piping only.
• The system should not disconnect a fire suppression water line or a fire sprinkler
water line.
• The Shutoff Valve should not be installed within a metal cabinet as this will prevent
it from communicating wirelessly with the Wally Hub.
Wally System
The Shutoff Valve works with the Wally Hub and Sensor to detect and prevent water
leaks. When a Sensor detects a leak, the Shutoff Valve turns off the main water supply to
prevent additional damage. Your Wally system can be configured to use any
Mounting the Shutoff Valve
1. Locate the most suitable place for installation on the water line.
2. Locate the water shutoff to your home and turn it off.
3. Mount the appropriate extension to the Shutoff Valve and install it on the
mounting pad using the attached screws, washers and nuts provided.
4. Once the Shutoff Valve is installed, push the lock inwards until it reaches a
mechanical limit.
Parallel
Mounting
using the long
adapter
Perpendicular
Mounting
using the short
adapter
A. Shutoff Valve motor
B. Motor stem position window
C. Indication RGB LED
D. Multipurpose button
E. Battery housing
F. Mounting fitting
G. Lock
H. Battery housing cover
Installing batteries in the Shutoff
Valve
1. Loosen the screw from the bottom of
the battery compartment.
2. Install the 4 included batteries as
instructed.
3. Replace the bottom battery
compartment and tighten the screw
to ensure a waterproof seal.
4. The Shutoff Valve will perform the
built-in Self-Test and the motor stem
will begin to turn.
A
B
C
D
E
H
F
G
Pairing the Shutoff Valve to Wally
1. Open up the Wally app on your mobile device (iOS or Android) or download it from
the Apple Store or Google Play Store.
2. Press the button on the Shutoff Valve once and the LED will begin to flash green.
3. From the Dashboard in the Wally app, tap “Add Product” and follow the
instructions.
4. When the Shutoff Valve has successfully paired the LED will stop flashing and the
Wally app will show a new tile on the Dashboard for the Shutoff Valve. You may tap
the Shutoff Valve tile to view more information and to control the valve remotely.
Shutoff Valve Alignment Reset
Performing a Shutoff Valve alignment is necessary in order to indicate to the Wally
Cloud that the Shutoff Valve is in the “CLOSED” position and thus prevents water
from flowing.
1. Align the slot on the top part of the Shutoff Valve motor stem perpendicular to
the water flow direction by single pressing the button until the flow of water has
stopped and the slot is perpendicular.
2. Set the closed state by pressing the button 5 times. This will program the Shutoff
Valve to know which way is closed versus open.
3. Once the alignment is reset, toggle the Shutoff Valve to the “OPENED” position
manually by pressing on the orange button twice.
Quick Start Guide-WSV.indd 2 5/8/17 12:47 PM