User's Manual
Table Of Contents
- Part A – Preface
- Safety Information
- Revision History
- Important Information
- Compliance Information
- Part B – Feature Overview
- Introduction
- Features and Benefits
- Q Data Radio Range
- Part C – System Topologies & Operating Modes
- System Topologies
- Operating Modes
- Part D – Feature Detail
- Hardware
- Efficiency and Bandwidth
- Connectivity
- Ease of Use
- Security
- Part E – Radio Planning and Design
- Radio Path analysis
- BER & Fade Margin
- Radio Accessories
- RF Feeders and Protection
- Part F – Quick Reference Guide
- Introduction
- Half Duplex Radio - QR450
- Full Duplex Radio - QB450
- Hot Standby Half Duplex Radio - QP450
- Hot Standby Full Duplex Radio - QH450
- LED indicators
- Connecting Antennas
- Communication Ports
- Activating Transmitter
- Factory Default
- Digital I/O
- Connecting to Web User Interface (WUI)
- Resolving Ethernet Connection Issues
- Part G– Quick Start Guide
- Step-by-Step Point to Point Setup
- Step-by-Step eDiags Setup
- System Topology Configuration
- Serial and MODBUS
- Single Frequency (Simplex) Mode
- E-Series Emulation Mode
- Part H – Advanced
- Connectivity
- Ease of Use
- Security
- Part I – Installation & Commissioning
- Optimising the Antenna for Rx Signal
- Commissioning
- Part J – Firmware Updating and Maintenance
- Firmware Updating
- Global Firmware Updating
- Fuse Replacement - QR450
- Part K – Open Source License Acknowledgements
- Part L – Support Options
120 Document Number: 0100SM1401 Issue: 05-15
Alarm Group:
operationalAlarm .1.3.6.1.4.1.33302.30.5.1.0 Integer Operational alarm
rxPllLocked .1.3.6.1.4.1.33302.30.5.2.0 Integer Receiver PLL lock status
radioVswrAlarmState .1.3.6.1.4.1.33302.30.5.10.1.2.1 Integer High VSWR
Normal =Operating within normal conditions,
UserAlarm =Operating outside of user
specified limits,
CriticalAlarm =Operating outside of specified
operating limits.
externalSupplyVoltageAlarmState .1.3.6.1.4.1.33302.30.5.11.0 Integer External supply voltage
Normal =Operating within normal conditions,
UserAlarm =Operating outside of user
specified limits,
CriticalAlarm =Operating outside of factory
specified operating limits.
temperatureAlarmState .1.3.6.1.4.1.33302.30.5.12.0 Integer Internal temperature.
Normal =Operating within normal conditions,
UserAlarm =Operating outside of user
specified limits,
CriticalAlarm =Operating outside of specified
operating limits.
radioRssiAlarmState .1.3.6.1.4.1.33302.30.5.13.1.2.1 Integer RSSI
Normal =Operating within normal conditions,
UserAlarm =Operating outside of user
specified limits.
radioTxPowerAlarmState .1.3.6.1.4.1.33302.30.5.14.1.2.1 Integer Tx Power
Normal =Operating within normal conditions,
UserAlarm =Operating outside of user
specified limits
globalAlarmState .1.3.6.1.4.1.33302.30.5.15.0 Integer Global Monitored Alarm.
Normal =All monitored parameters are
operating within normal conditions,
UserAlarm =One or more monitored
parameters are operating outside of user
specified limits,
CriticalAlarm =One or more monitored
parameters are operating outside of factory
specified operating limits.
txPllLocked .1.3.6.1.4.1.33302.30.5.17.0 Integer Transmit PLL lock status
radioFrequencyAlarmState .1.3.6.1.4.1.33302.30.5.18.0 Integer Frequency error state.
Normal =Operating within normal conditions,
UserAlarm =Receive frequency error out of
user specified limits.
Part H – Advanced