User's Manual
Table Of Contents
- Part A – Preface
- Safety Information
- Revision History
- Important Information
- Compliance Information
- Part B – Feature Overview
- Introduction
- Features and Benefits
- Q Data Radio Range
- Part C – System Topologies & Operating Modes
- System Topologies
- Operating Modes
- Part D – Feature Detail
- Hardware
- Efficiency and Bandwidth
- Connectivity
- Ease of Use
- Security
- Part E – Radio Planning and Design
- Radio Path analysis
- BER & Fade Margin
- Radio Accessories
- RF Feeders and Protection
- Part F – Quick Reference Guide
- Introduction
- Half Duplex Radio - QR450
- Full Duplex Radio - QB450
- Hot Standby Half Duplex Radio - QP450
- Hot Standby Full Duplex Radio - QH450
- LED indicators
- Connecting Antennas
- Communication Ports
- Activating Transmitter
- Factory Default
- Digital I/O
- Connecting to Web User Interface (WUI)
- Resolving Ethernet Connection Issues
- Part G– Quick Start Guide
- Step-by-Step Point to Point Setup
- Step-by-Step eDiags Setup
- System Topology Configuration
- Serial and MODBUS
- Single Frequency (Simplex) Mode
- E-Series Emulation Mode
- Part H – Advanced
- Connectivity
- Ease of Use
- Security
- Part I – Installation & Commissioning
- Optimising the Antenna for Rx Signal
- Commissioning
- Part J – Firmware Updating and Maintenance
- Firmware Updating
- Global Firmware Updating
- Fuse Replacement - QR450
- Part K – Open Source License Acknowledgements
- Part L – Support Options
119
Document Number: 0100SM1401 Issue: 05-15
Object name Object Identifier (OID) Syntax Object description
Security Group:
snmpVersion .1.3.6.1.4.1.33302.30.3.1.0 Integer Default SNMP version
consoleLoginStatus1 .1.3.6.1.4.1.33302.30.3.2.0 Integer Console login status for COM1
consoleLoginStatus2 .1.3.6.1.4.1.33302.30.3.3.0 Integer Console login status for COM2
numberOfActiveTelnetSessions .1.3.6.1.4.1.33302.30.3.4.0 Integer Number of active Telnet sessions
telnetSessionTable .1.3.6.1.4.1.33302.30.3.5 Integer Table of Telnet and Ssh sessions
telnetSessionStatus .1.3.6.1.4.1.33302.30.3.5.1.2* Integer Telnet or Ssh session status
telnetSessionIp .1.3.6.1.4.1.33302.30.3.5.1.3* String Telnet or Ssh session remote ip address
encryptionStatus .1.3.6.1.4.1.33302.30.3.11.0 Integer Encryption status
ETH Group:
interfaceName .1.3.6.1.4.1.33302.30.4.1.1.2.x String Ethernet interface (row) name (where x is
the Ethernet interface - 1 (ETH1), 2 (ETH2)
or 3 (ETH3)
interfaceStatus .1.3.6.1.4.1.33302.30.4.1.1.3.x Integer Ethernet interface status (where x is the
Ethernet interface - 1 (ETH1), 2 (ETH2) or
3 (ETH3)
interfaceSpeed .1.3.6.1.4.1.33302.30.4.1.1.4.x Integer Ethernet interface link speed (where x is the
Ethernet interface: 1 (ETH1), 2 (ETH2) or 3
(ETH3)
interfaceMode .1.3.6.1.4.1.33302.30.4.1.1.5.x Integer Ethernet interface link mode (where x is the
Ethernet interface - 1 (ETH1), 2 (ETH2) or
3 (ETH3)
Base Station Group:
digitalInputTable .1.3.6.1.4.1.33302.30.6.2 Table of base station digital inputs.
digitalOutputTable .1.3.6.1.4.1.33302.30.6.3 Table of base station digital outputs.
chassisFanStatusTable .1.3.6.1.4.1.33302.30.6.4 Table of chassis fan status.
internalOnlineModule .1.3.6.1.4.1.33302.30.6.5.0 Internal current online module.
When operating in full duplex mode, this is the primary unit.
When operating in protected half duplex mode, this is the
unit that is currently online.
Part H – Advanced