ASSEMBLY GUIDE TS60-1010 Platform Scale Series 2 V 2.
Assembly Guide TS60-1010 Platform Scale TABLE OF CONTENTS OVERVIEW General Specifications ................................................................................................................1 Cautions and Disclaimers...........................................................................................................1 Contents of Kit ............................................................................................................................1 Tools Required For Assembly....
Assembly Guide TS60-1010 Platform Scale Triner Scale Model TS60-1010 Series 2 Platform Scale OVERVIEW General Specifications • Platform Size: 10' (L) x 10' (W) x 8.5" (H) • Ramps: 49" (L) x 10' (W) x 8.
Assembly Guide TS60-1010 Platform Scale Tools Required For Assembly Forklift Impact Wrench 19mm Socket Wrench 30mm Socket Wrench 5 lb Rubber Mallet Long pry bar 5/16” Allen wrench Standard Size Flat Head Screw Driver Small Flat Head Screw Driver Hammer Drill: ¾” bit & ½” bit Adjustable Wrench or 27mm Wrench Time Required to Assemble 4-5 hours 2
Assembly Guide TS60-1010 Platform Scale ASSEMBLING THE SCALE IMPORTANT! Before beginning with assembly of the scale, thoroughly read and understand this Assembly Guide. Review the illustration Figures 1a and 1b in the Appendix section. Become familiar with the basic configuration of the weighing deck and the identifying markings on the components. All figures containing the supporting illustrations and photos are located in the Appendix section in the back of this guide.
Assembly Guide TS60-1010 Platform Scale Forklift Weighing Deck #1 into position between the rails, and gently lower the deck down onto the wooden blocks. Be sure to accurately line up the front edge of the deck to the front edge of both side rails. Loosely bolt the weighing deck to the side rails. NOTE: Only use short bolts when bolting next to a load cell! Refer to Fig. 1c.
Assembly Guide TS60-1010 Platform Scale around the scale, alternating from side to side in order to gradually bring all components together in a proper fit. Before final tightening, loosely bolt down the top plate, then fully tighten after the rail/platform bolts have been secured. 7) Attach and Securely Fasten the Two Guard Rails Attach both guard rails using the bolts provided. Securely tighten all bolts.
Assembly Guide TS60-1010 Platform Scale 11) Attach the Ramps to the Weighing Base SYNOPSIS: The ramps are placed into position at the end of the weighing deck, then the weighing deck is lowered to the floor, one corner at a time. The two load cell feet at the end of the weighing deck fit into holes in the ramp tabs, as shown in Fig. 9.
Assembly Guide TS60-1010 Platform Scale 14) Bolt Down Both Ramps to the Concrete Floor Using a hammer drill, drill 3/4” holes into the concrete for anchoring the floor mounting tabs to the floor. Use the provided concrete anchors and securely fasten all four ramps tabs to the floor. 15) Bolt Down the Four Deck Top Access Panels Securely bolt down the access panels, lightly tightening the four corner bolts on the panel, then working from side to side tightening the other bolts. Secrely tighten all bolts.
Assembly Guide TS60-1010 Platform Scale Appendix Figure 1a COMPLETE ASSEMBLY i
Assembly Guide TS60-1010 Platform Scale Appendix Figure 1b WEIGHING DECK ASSEMBLY ii
Assembly Guide TS60-1010 Platform Scale Appendix Figure 1c RAMP MOUNTING TABS AND HANDLING PRECAUTIONS iii
Assembly Guide TS60-1010 Platform Scale Appendix Figure 2 PLACE SIDE RAILS ONTO WOOD BLOCKS Figure 3 PLACE THE FIRST DECK INTO POSITION AND LOOSELY BOLT TO SIDE RAILS iv
Assembly Guide TS60-1010 Platform Scale Appendix Figure 4 ONLY USE SHORT BOLTS NEXT TO LOAD CELLS Figure 5 ROUTING THE LOAD CELL CABLES v
Assembly Guide TS60-1010 Platform Scale Appendix Figure 6 PLACE THE SECOND DECK INTO POSITION AND LOOSELY BOLT TO SIDE RAILS vi
Assembly Guide TS60-1010 Platform Scale Appendix Figure 7 JUNCTION BOX, Wiring Diagram vii
Assembly Guide TS60-1010 Platform Scale Appendix Figure 8 JUNCTION BOX, Attached at Side Rail #1 Figure 9 ALIGN RAMP TAB TO WEIGHING DECK LOAD CELL FOOT viii
Assembly Guide TS60-1010 Platform Scale Appendix Figure 10 MOVE RAMP INTO POSITION UNDER WEIGHING DECK LOAD CELL FOOT Figure 11 FULLY ASSEMBLED SCALE ix
TRINER SCALE & MFG. CO. LIMITED WARRANTY What is Covered: Triner Scale & Mfg. Co. Inc. warrants to the first end user customer of the Triner Scale product enclosed with this limited warranty statement that the product, if purchased and used in the United States, conforms to the manufacturer’s specifications and will be free from defects in workmanship and materials for a period of two (2) years from the date of original purchase.
