User Manual
Table Of Contents
- 1 Features
- 2 First Steps with TMCL
- 3 TMCL and the TMCL-IDE — An Introduction
- 3.1 Binary Command Format
- 3.2 Reply Format
- 3.3 Standalone Applications
- 3.4 The ASCII Interface
- 3.5 TMCL Command Overview
- 3.6 TMCL Commands by Subject
- 3.7 Detailed TMCL Command Descriptions
- 3.7.1 ROR (Rotate Right)
- 3.7.2 ROL (Rotate Left)
- 3.7.3 MST (Motor Stop)
- 3.7.4 MVP (Move to Position)
- 3.7.5 SAP (Set Axis Parameter)
- 3.7.6 GAP (Get Axis Parameter)
- 3.7.7 STAP (Store Axis Parameter)
- 3.7.8 RSAP (Restore Axis Parameter)
- 3.7.9 SGP (Set Global Parameter)
- 3.7.10 GGP (Get Global Parameter)
- 3.7.11 STGP (Store Global Parameter)
- 3.7.12 RSGP (Restore Global Parameter)
- 3.7.13 RFS (Reference Search)
- 3.7.14 SIO (Set Output)
- 3.7.15 GIO (Get Input)
- 3.7.16 CALC (Calculate)
- 3.7.17 COMP (Compare)
- 3.7.18 JC (Jump conditional)
- 3.7.19 JA (Jump always)
- 3.7.20 CSUB (Call Subroutine)
- 3.7.21 RSUB (Return from Subroutine)
- 3.7.22 WAIT (Wait for an Event to occur)
- 3.7.23 STOP (Stop TMCL Program Execution – End of TMCL Program)
- 3.7.24 SCO (Set Coordinate)
- 3.7.25 GCO (Get Coordinate)
- 3.7.26 CCO (Capture Coordinate)
- 3.7.27 ACO (Accu to Coordinate)
- 3.7.28 CALCX (Calculate using the X Register)
- 3.7.29 AAP (Accu to Axis Parameter)
- 3.7.30 AGP (Accu to Global Parameter)
- 3.7.31 CLE (Clear Error Flags)
- 3.7.32 EI (Enable Interrupt)
- 3.7.33 DI (Disable Interrupt)
- 3.7.34 VECT (Define Interrupt Vector)
- 3.7.35 RETI (Return from Interrupt)
- 3.7.36 Customer specific Command Extensions (UF0…UF7 – User Functions)
- 3.7.37 Request Target Position reached Event
- 3.7.38 TMCL Control Commands
- 4 Axis Parameters
- 5 Global Parameters
- 6 Module Specific Hints
- 7 Hints and Tips
- 8 TMCL Programming Techniques and Structure
- 9 Figures Index
- 10 Tables Index
- 11 Supplemental Directives
- 12 Revision History
PD-1160 TMCL
™
Firmware Manual • Firmware Version V1.42 | Document Revision V1.06 • 2018-JAN-09
78 / 113
Number Axis Parameter Description Range [Units] Access
138 Ramp mode
Automatically set when using ROR, ROL, MST
and MVP.
0: Position mode. Steps are generated, when the
parameters actual position and target position
differ. Trapezoidal speed ramps are provided.
2: Velocity mode. The motor will run continu-
ously and the speed will be changed using the
maximum acceleration parameter when the tar-
get speed gets changed.
For special purposes, the soft mode (value 1)
with exponential decrease of speed can be se-
lected.
0/1/2 RW
140 Microstep
resolution
Microstep resolutions per full step:
0 fullstep
1 halfstep
2 4 microsteps
3 8 microsteps
4 16 microsteps
5 32 microsteps
6 64 microsteps
7 128 microsteps
8 256 microsteps
It is strongly recommended to use at least 8
microsteps.
0. . . 8 RW
149 Soft stop flag 0 - Hard stop when a stop switch is hit.
1 - Soft stop (using deceleration ramp) when a
stop switch is hit.
0/1 RWE
150 End switch
power down
mode
0 - Stay at run current when stopped by end
switch.
1 - Use stand by current when stopped by end
switch.
0/1 RW
153 Ramp divisor
The exponent of the scaling factor for the ramp
generator. Change this parameter carefully (in
steps of one) and only while the motor is not
moving. Lower values lead to higher accelera-
tions.
This parameter specifies the relation between
internal and real world acceleration units.
0. . . 13 RWE
©2018 TRINAMIC Motion Control GmbH & Co. KG, Hamburg, Germany
Terms of delivery and rights to technical change reserved.
Download newest version at www.trinamic.com