User's Manual

ManualsBrandsTrimble ManualsElectronicsGNSS RX with Bluetooth and Spread Spectrum Radio

Table Of Contents

USER GUIDE
Legal Notices
Safety Information
- Regulations and safety
- Type approval
- Exposure to radio frequency radiation
- Installing antennas
- Battery safety
Contents
Introduction
- About the SPSx80 Smart GPS antenna
- About the SPSx81 Smart GPS antenna
- Related Information
- Technical Support
- Your Comments
Features and Functions
- Overview
- SPS780 Smart GPS antenna features
- SPS781 Smart GPS antenna standard features
- SPS880 Extreme Smart GPS antenna standard features
- SPS881 Extreme Smart GPS antenna standard features
- Use and care
- COCOM limits
- Parts of the receiver
  - Front panel
  - Lower housing
- Button functions
- LED behavior
  - LED flash patterns
Batteries and Power
- External power
- Battery safety
- Battery performance
- Charging the Lithium-ion batteries
- Storing the Lithium-ion battery
- Disposing of the rechargeable Lithium-ion battery
Setup Guidelines
- Base station operation guidelines
  - Base station components
  - Base station setup guidelines
- Rover operation guidelines
  - Rover receiver components
  - Rover receiver setup guidelines
- Cellular modem and external radio
Setting up the Receiver
- Connecting the receiver to external devices
  - Trimble controller with SCS900 Site Controller software
  - External radio-modems
- Common ways to set up a base station
- Common ways to set up a rover receiver
Configuring the Receiver Settings
- Using the SCS900 Site Controller software to configure the base station, the rover, and the radios
- Configuring the receiver to log data for postprocessing
- Configuring the receiver in real time
- Configuring the receiver using application files
- Creating and editing the configuration files that control the receiver
AutoBase Feature
- Setting Up a Base Station
  - Best practice
  - Antenna type
- Scenarios
- AutoBase process
Default Settings
- Default receiver settings
- Resetting the receiver to factory defaults
- Default behavior
- Power up settings
- Logging data
  - Logging data after a power loss
Specifications
- General specifications
- Physical specifications
- Electrical specifications
- Communication specifications
- GPS satellite signal tracking
- Integrated radio options
- Variable configuration options
NMEA-0183 Output
- NMEA-0183 message overview
- Common message elements
  - Message values
- NMEA messages
- ADV
- GGA
- GSA
- GST
- GSV
- HDT
- PTNL,AVR
- PTNL,GGK
- PTNL,PJK
- PTNL,VGK
- PTNL,VHD
- RMC
- ROT
- VTG
- ZDA
GSOF Messages
- Supported message types
- General Serial Output Format
- Reading binary values
  - INTEGER data types
- GSOF message definitions
Adding Internal Radio Frequencies
- Adding receive frequencies for the 450 MHz internal radio
Real-Time Data and Services
- RT17 Streamed Data service
- Login authentication
Upgrading the Receiver Firmware
- The WinFlash utility
  - Installing the WinFlash utility
- Upgrading the receiver firmware
Data Logging and Postprocessed Measurement Operations
- Connecting to the office computer
- Transferring files directly from a CompactFlash card
- Deleting files in the receiver
- Supported file types
Troubleshooting
- LED conditions
- Receiver issues
- Base station setup and static measurement problems
Glossary

4 Setup Guidelines

38 SPSx80 and SPSx81 Smart GPS Antennas User Guide

– Cellular modem or a cellular phone that can transmit data

• Serial (cell phone to DB9) cable (supplied with the cellular modem or phone).

• Port 2 of the Smart GPS antenna supports full RS-232 protocol, and should

function properly with most cell phone cables. Some cellular units may require

custom cabling.

Alternatively, the receiver also supports a cable-free Bluetooth connection with

Bluetooth-enabled cell phones.

For more information on using a cellular modem as a data link, refer to the SCS900 Site

Controller Software Getting Started Guide and SCS900 Site Controller Software Office

Guide.