User Manual

ManualsBrandsTrimble ManualsElectronicsGPS Receiver with Bluetooth

Table Of Contents

5700/5800 GPS Receiver
Contents
About This Manual
- Related Information
- Technical Assistance
- Your Comments
- Document Conventions
5700 GPS receiver
Overview
- Introduction
- Features
- Use and Care
- COCOM Limits
Setting up the Receiver
- Introduction
- Parts of the Receiver
- Setup Guidelines
- Postprocessed Setup
- PoleMounted Setup
- Backpack Setup
- Other System Components
General Operation
- Introduction
- Button Functions
- LED Behavior
- Starting and Stopping the Receiver
- Logging Data
  - Logging Internally
  - Logging to Trimble Survey Controller
- Resetting to Defaults
- Formatting a CompactFlash Card
- Batteries and Power
- Battery charging and storage
Configuration
- Introduction
- Configuring the Receiver in Real Time
- Configuring the Receiver Using Application Files
- Application Files
Transferring Data
- Introduction
- Connecting to the Office Computer
- Transferring Data
- Transferring Files Directly from a CompactFlash Card
- Deleting Files in the Receiver
- Supported File Types
Software Utilities
- Introduction
- GPS Configurator Software
  - Installing GPS Configurator
  - Configuring the 5700 Receiver
- Configuration Toolbox Software
  - Installing Configuration Toolbox
  - Creating and Editing Application Files
- WinFLASH Software
Specifications
- Introduction
- Physical Specifications
- Positioning Specifications
- Technical Specifications
Default Settings
- Introduction
- Default Settings
- Resetting to Factory Defaults
- Examples
Cables and Connectors
- Introduction
- Port 1, 2, and 3 Connectors
- power/serial data Cable
- Event Marker/1PPS Cable
- GPS Antennas and Cables
Event Marker Input and 1PPS Output
- Introduction
- Event Marker Input
  - Enabling and Configuring Event Marker Input
- 1PPS Output
5800 GPS receiver
Overview
- Introduction
- Regulations and Safety
  - Type Approval
  - Safety
- Features
- Use and Care
- COCOM Limits
Setting up the Receiver
- Introduction
- Parts of the Receiver
  - Front Panel
  - Lower Housing
- Setup Guidelines
- PoleMounted Setup
- Other System Components
  - Radios
  - Cellular Modems and External Radios
General Operation
- Introduction
- Button Functions
- LED Behavior
  - LED Flash Patterns
- Starting and Stopping the Receiver
- Logging Data
  - Logging to Trimble Survey Controller
- Resetting to Defaults
- Batteries and Power
  - Power Output
  - Firmware
Configuration
- Introduction
- Configuring the Receiver in Real Time
- Configuring the Receiver Using Application Files
- Application Files
Software Utilities
- Introduction
- GPS Configurator Software
  - Installing GPS Configurator
  - Configuring the 5800 Receiver
- Configuration Toolbox Software
  - Installing Configuration Toolbox
  - Creating and Editing Application Files
- WinFLASH Software
Specifications
- Introduction
- Physical Specifications
- Positioning Specifications
- Technical Specifications
Default Settings
- Introduction
- Default Settings
- Resetting to Factory Defaults
  - Default Behavior
  - Power up Settings
Cables and Connectors
- Introduction
- Port 1 and 2 Connectors
- Power/Serial Data Cables
5700 & 5800 Appendixes
NMEA-0183 Output
- Introduction
- NMEA-0183 Outputs
- Common Message Elements
  - Message Values
- NMEA Messages
Troubleshooting
Index

2 Setting up the Receiver

44 5700/5800 GPS Receiver User Guide

5700 Operation

Figure 2.16 shows the components required to connect an antenna to a

5700 receiver with an antenna power adapter. When setting up the

antenna power adapter, connect all other cables before you connect the

power supply.

Figure 2.15 Connecting an antenna with an antenna power adapter

To power supply

Antenna

power adapter