User's Manual

ManualsBrandsTrimble Navigation ManualsElectronicsUHF Radio

100

Table Of Contents

Safety Information
- Rechargeable Lithium-Ion Batteries
Introduction
- Related Information
- Warnings and Cautions
- Technical Assistance
- Your Comments
Trimble R7 GPS Receiver
Overview
- Features
- Use and Care
- COCOM Limits
Setting up the Receiver
- Parts of the Receiver
- Setup Guidelines
- Postprocessed Setup
- PoleMounted Setup
- Backpack Setup
- Other System Components
General Operation
- Button Functions
- LED Behavior
- Starting and Stopping the Receiver
- Logging Data
  - Logging internally
  - Logging to a Trimble controller
- Resetting to Defaults
- Formatting a CompactFlash Card
- Batteries and Power
Configuration
- Configuring the Receiver in Real Time
- Configuring the Receiver Using Application Files
- Application Files
Transferring Data
- Connecting to the Office Computer
- Transferring Data
- Transferring Files Directly from a CompactFlash Card
- Deleting Files in the Receiver
- Supported File Types
Software Utilities
- The GPS Configurator Software
  - Installing the GPS Configurator software
  - Configuring the Trimble R7 receiver using the GPS Configurator software
- The WinFlash Software
Specifications
- Physical Specifications
- Positioning Specifications
- Technical Specifications
Default Settings
- Default Settings
- Resetting to Factory Defaults
- Examples
Cables and Connectors
- Port 1, 2, and 3 Connectors
- Power/serial data cable
- Event Marker/1PPS Cable
- GPS Antennas and Cables
Event Marker Input and 1PPS Output
- Event Marker Input
  - Enabling and configuring event marker input
- 1PPS Output
Trimble R8 GPS Receiver
Overview
- Features
- Use and Care
- COCOM Limits
Setting up the Receiver
- Parts of the Receiver
  - Front panel
  - Lower housing
- Setup Guidelines
- PoleMounted Setup
- Other System Components
  - Radios
  - Cellular modems and external radios
General Operation
- Button Functions
- LED Behavior
  - LED flash patterns
- Starting and Stopping the Receiver
- Logging Data
  - Logging internally
  - Logging to a Trimble controller
- Resetting to Defaults
- Batteries and Power
Configuration
- Configuring the Receiver in Real Time
- Configuring the Receiver Using Application Files
- Application Files
Software Utilities
- The GPS Configurator Software
  - Installing the GPS Configurator software
- The WinFlash Software
Specifications
- Physical Specifications
- Positioning Specifications
- Technical Specifications
Default Settings
- Default Settings
- Resetting to Factory Defaults
  - Default behavior
  - Power up settings
Cables and Connectors
- Port 1 and 2 Connectors
- Power/Serial Data Cables
Appendixes Trimble R7 / Trimble R8
NMEA-0183 Output
- NMEA-0183 Outputs
- Common Message Elements
  - Message values
- NMEA Messages
RTCM Output
- Generated Messages
- Message Scheduling
Troubleshooting
Index

Trimble R7/R8 GPS Receiver User Guide 81

Default Settings 9

Trimble R7 GPS Receiver Operation

Serial Port 2: Baud rate 38400

Format 8-None-1

Serial Port 3: Baud rate 38400

Format 8-None-1

Flow control None

Input Setup: Station Any

NMEA/ASCII (all messages) All Ports Off

Streamed output All Types Off

Offset = 00

RT17/Binary All Ports Off

CMR output [Static] CMR: cref ID 0000

RTCM output RTCM: Type 1 ID 0000

Reference position: Latitude 0°

Longitude 0°

Altitude 0.00 m HAE

Antenna: Type Unknown external

Height (true vertical) 0.00 m

Group All

Measurement method Bottom of antenna mount

Logging rate 15 sec

Position rate 5 min

Measurement rate 10 Hz

Table 9.1 Default settings (continued)

Function Factory Default