Installation Manual

SkyConnector Indoor
Installation Guide
E
P
C
:GN
INRAW
REP
O
RPMI
N
OITALLATSNI
EGAMA
D
DLUOC
R
E
TUPMOCRUOY
R
E
WOP
RET
UP
M
O
C
EPC
EPC
:GNINRAW
R
EP
ORPMI
NOITALLATSNI
E
G
A
M
A
DDLUO
C
R
ETU
P
MOCR
U
OY
RE
W
O
P
R
E
T
UP
MOC
Power on
2
Plug one end of the 25-foot Ethernet cable into the RJ-45 port on the SkyConnector and
the other end into the port labeled “CPE” on the power injector.
Connect the AC adapter to the power injector, and plug the adapter into an AC outlet.
The Power LED lights to indicate the device is powered on.
RJ-45 port
Ethernet
cable
Move the SkyConnector to dierent parts of the building to nd the strongest SkyPilot
network signal. When the SkyConnector detects a signal, the WAN Act (WAN Activity)
LED starts to blink. (The faster the LED blinks, the stronger the signal.) If the WAN Act
LED does not start blinking within 30 seconds, try another location.
90 seconds after a signal is located, the WAN Link LED should start blinking, slowly then
more rapidly. When the WAN Link LED turn solid, you are connected to the network.
PWR
LAN WAN
LinkLink ActAct
Remove the adhesive backing from the four foot pads and place them on the underside
of the desk stand.
Place the SkyConnector in the desk stand and insert the two knobs as shown. Tighten
the knobs to secure the device.
Attach stand
2
1
Attach one end of the 7-foot Ethernet cable to the port labeled “Computer” on the power
injector and the other end into an Ethernet port on your personal computer or other
network device, such as a router.
When SkyConnector Indoor is properly connected to the computer, the LAN Link LED
lights to indicate a successful connection between the devices.
Connect computer
4
Your SkyPilot™ SkyConnector™
Indoor kit provides everything you
need to set up your SkyConnector
and connect to a provider’s wireless
mesh network.
Contents of the kit
• SkyConnector Indoor
• Desk stand and mounting knobs
• Power injector
• AC adapter
• Mounting hardware
• Two Ethernet cables (25-foot
and 7-foot)
About the SkyConnector
Your SkyConnector is a plug-and-
play device that connects you to a
SkyPilot wireless network providing
wireless access to the Internet.
For optimal operation, you need to
place the SkyConnector in a loca-
tion that has a line of sight to other
SkyPilot equipment.
2055 Laurelwood Road
Santa Clara, CA 95054-2747
[phone] or
(866) SKYPILOT
www.skypilot.com
What‘s next?
Review the documentation provided to you
by your service provider for instructions on
conguring your computer for access to the
Internet as well as broadband applications
and services.
AC adapter
power injector
mounting knob
computer
desk stand
Locate signal
3
Blinking WAN Act LED indi-
cates network signal.
PWR
LAN WAN
LinkLink ActAct
Solid WAN Act LED indi-
cates network connection.
PWR
LAN WAN
Link Link Act Act
Solid LAN Link light indicates
successful connection with
computer.
RJ-45 port
Network information
ISP help desk
IP address
Netmask
DNS (name servers)
© 2006 SkyPilot Networks, Inc. All rights reserved. SkyConnector, SkyPilot,
SkyPilot Networks, the SkyPilot logo, and other designated trademarks, trade
names, logos, and brands are the property of SkyPilot Networks, Inc. or their
respective owners. Product specications are subject to change without notice.
This material is provided for informational purposes only; SkyPilot assumes
no liability related to its use and expressly disclaims any implied warranties of
merchantability or tness for any particular purpose.