User's Manual
Table Of Contents
- Chapter 1
- General Information
- Helpful Website
- Where to Get Technical Support
- How this Manual is Organized
- Optional Software
- Conventions Used in this Manual
- Precautions
- Chapter 2
- Seeker Introduction
- What is the Seeker?
- Seeker Features
- Easy Frequency Configuration
- Multiple Frequency Presets
- Channel Tag Compatibility
- GT Noise Discrimination
- Squelch Operation
- Source Localization
- Vehicle Battery Protection
- Equipment Supplied with Your Seeker
- Accessories & Replacement Parts for Your Seeker
- A Guided Tour of Your Seeker
- Front View
- Back View
- Right Side View
- Bottom View
- Display Screen
- A Guided Tour of Your Mobile Mount
- Front View
- Left Side View
- Rear View
- About Your Seeker’s Battery
- Overview
- If Your Seeker Does Not Turn On
- Checking the Battery Level
- Charging the Battery
- Updating Your Seeker’s Firmware
- Chapter 3
- Seeker Operation
- Configure Settings
- Seeker’s Operation Modes
- Measurement Mode
- PC Communications Mode
- Display Modes
- Signal Level
- Battery Charge Level
- Peak Hold
- Preset Frequencies
- Channel Tag
- Snapshot Modes
- Pre-Fix
- Post-Fix
- No Snapshot
- Chapter 4
- Leakage Testing
- Before You Begin Leakage Testing
- Testing For Leaks
- Chapter 5
- Seeker MCA III Introduction
- What is Seeker GPS?
- Equipment Supplied with Your Seeker MCA III
- Accessories for Your Seeker MCA III
- Device Overview
- Front View
- Left Side View
- Rear View
- Display Screen Overview
- Chapter 6
- Seeker MCA III Operation
- Configure Settings
- Seeker GPS Display Modes
- Mobile Mount Communication Successful
- GPS Signal
- Data Synchronization
- Chapter 7
- Data Upload Options
- Standard Internet Connection
- Wi-Fi
- Fleet Management System Integration
- Chapter 8
- Appendix
- General Specifications
- Display Messages & Error Codes
- Seeker Error Codes
- MCA III Error Codes
- Access Point Error Codes
- Seeker & MCA II Communication Messages
- Seeker & MCA II Memory Full Messages
- Trilithic Broadband Instruments 2-Year Limited Warranty
55
Seeker & Seeker MCA III Operation Manual
“E##”
Code
ErrorDescription Solution
12
WEP key
communications failed
Check to ensure that your WEP key is valid and
recongurethedeviceusingthecorrectWEPkey.
13
WPA key
communications failed
Check to ensure that your WPA/WPA2 key is valid
andrecongurethedeviceusingthecorrectWPA/
WPA2 key.
14
WiFi signal level
communications failed
If the error persists, contact support as this error may
requirearmwareupdatetocorrect.
30
Flash memory erasure
error
If the error persists, return the device to the factory
for repair.
31
Cellular modem
communications error
If the error persists, contact support as this error
mayrequirearmwareupdatetocorrect.Iftheerror
persists, return the device to the factory for repair.
32
Cellular connection
could not obtain an IP
If the error persists, contact support as this error
mayrequirearmwareupdatetocorrect.Iftheerror
persists, contact your cellular data provider for further
support.
33
Cellular connection
could not establish a
network socket to the
desired end point
Check to ensure that your connection settings are
correctandrecongurethedeviceusingthecorrect
information.
34
No data erasure
command received from
LAW after data upload
Ifthiserrorpersists,contactsupporttoconrmthat
your LAW server is set up correctly.
35 Upload stopped
Ethernet communications attempt caused an upload
to be postponed. Information only, uploading was
postponed due to a Seeker Setup connection
attempt.