Tus neeg siv phau ntawv
INSTALLATION INSTRUCTIONS
PROGRAMMING THE COUNTDOWN TIMER
®®
INTRODUCTION
GETTING TO KNOW THE PRODUCT
SensorClick™ is a revolutionary, modular power platform that
offers a broad selection of energy-saving surge protectors and
sensors that seamlessly work together to reduce energy waste.
With an extensive and growing list of sensors, you can quickly
and inexpensively set up a custom power management solution
for any application.
The TS1801TF SensorClick 4-outlet Advanced PowerTap with
Timer Footswitch saves energy by providing users with manual
and timed control over power supplied to electronics plugged
into the switched outlets.
LED indicators
Surge LED: When illuminated green, this
LED indicates that the surge protection is
functioning normally. If this LED illuminates
red or extinguishes at any time, the Product
was sacrificed to protect your devices and
must be replaced.
Ground LED: When illuminated green, this
LED indicates that the Product is correctly
grounded. If not illuminated, there is a
grounding problem, and you must contact
an electrician to properly ground the outlet.
Surge protection will not work with an
improperly grounded outlet.
Switched LED: When illuminated green,
this LED indicates that the switched outlets
are receiving power.
RJ11 sensor port
Plug the timer footswitch into this port.
There will be a soft audible ‘click’ when the
connector is inserted correctly.
The timer footswitch must be plugged into
the RJ11 sensor port in order for the
switched outlets to function correctly.
Resettable circuit breaker
The Product provide surge protection for all
outlets. If no devices are powered or the
LEDs are not illuminated, press the circuit
breaker switch to “RESET” to reactivate
power.
Always-on outlets
The always-on outlets receive continuous
power and remain on all of the time.
Switched outlets
The switched outlets are controlled by the
timer footswitch. The power supplied to the
switched outlets is removed and restored by
pressing the on/off button, and power
supplied to the switched outlets is removed if
the countdown timer expires. The switched
outlets will remain off if the timer footswitch is
not connected.
< > outlet
The first switched outlet, marked < > senses
current and determines the state of the
device plugged into it. This status is used by
the timer footswitch to determine if the
connected device is on or off and to provide
extra energy saving features.
SensorClick Timer Footswitch
The timer footswitch features a manual
on/off button and configurable countdown
timer. It connects to the power strip via the
RJ11 port marked “sensor,” and should be
placed in an easy-to-reach location (e.g.
under the desk).
Important: The product must only be plugged into a grounded outlet receptacle. All connected electronics should be plugged directly into
the product. Use of an extension cord, adapter, or any power strip in conjunction with the Product will void all warranties.
!
There is no power supplied to the switched outlets.
The SensorClick timer footswitch must be connected to the power tap. If power is not supplied to switched outlets, press the button on the timer
footswitch to manually turn on the switched outlets.
!
The SensorClick timer footswitch is blinking and an alarm is sounding.
This is a notification that countdown timer period is about to expire, and that the electronics plugged into the switched outlets will soon shut off. To
reset the timer, press the button on the timer footswitch.
!
!
TROUBLESHOOTING
There is no power supplied to any of the outlets.
Ensure that the circuit breaker switch on the top of the power tap is not set to off. If so, flip the switch to reset the circuit breaker.
!
The SensorClick timer footswitch has a configurable countdown timer that can be set to 1-10 hours (one-hour increments).
To configure the countdown timer, press and hold the button on top of the timer footswitch for 5 seconds until the LED
illuminates. Then press the button the number of times (1-10) to program countdown timer for the respective number of hours,
for example:
• Once for 1 hour
• Two times for 2 hours
• ...Up to 10 times for 10 hours
Press and hold the button for 5 seconds again to set the countdown timer. After the countdown timer is set, the LED will flash
the same number of times the button was pressed to confirm the new timer setting.
INSTALLATION INSTRUCTIONS
Plug in devices that require continuous
power into the always-on outlets (e.g.,
modem, CPU).
Plug peripheral electronics into the outlets
on the powertap labeled “switched.”
surge
ground
switched
switched always on
Step 1
< tv >
surge
ground
switched
switched always on
Step 2
sensor
high
low
threshold
Step 3
Set the adjustable threshold switch to
“low” when using a monitor as the control
device and “high” when using the TV as a
control device.
Plug the SensorClick timer footswitch into
the port on the side of the power tap that
looks like a phone jack and is marked
“sensor”.
Place the timer footswitch in a location
(e.g. under the desk) within reach of your
foot .
sensor
high
low
threshold
Step 4 Step 5 Step 6
Plug the powertap into a grounded outlet
receptacle. The ground and surge lights
on the powertap will illuminate indicating
that the powertap is properly grounded,
and that surge protection is active.
sensor
surge
ground
switched
surge
ground
switched
always on
RESET
OFF
surge
ground
switched
switched always on
always on
surge
ground
switched
switched always on