User manual

2
IMPORTANT SAFETY INFORMATION
It is most important that this instruction book should be retained with the appliance for future
reference. Should the appliance be sold or transferred to another owner, or should you move house and
leave the appliance, always ensure that the book is left with the appliance in order that the new owner
can get to know the functioning of the appliance and the relevant safety information.
This information has been provided in the interest of safety. You MUST read it carefully before installing
or using the appliance.
Installation
¥ This appliance is heavy. Care should be taken
when moving it.
¥ It is dangerous to alter the specifications or
attempt to modify this product in any way.
¥ Care must be taken to ensure that the appliance
does not stand on the electrical supply cable. If
the supply cord is damaged, it must be replaced
by a special cable available from your local
Service Force Centre.
¥ Any electrical work required to install this
appliance should be carried out by a qualified
electrician or competent person.
¥ Parts which heat up should not be exposed.
Whenever possible, the back of the appliance
should be close to a wall but leaving the required
distance for ventilation as stated in the installation
instructions.
¥ The appliance should be left for 2 hours after
installation before it is turned on, in order to allow
the refrigerant to settle.
Child Safety
¥ Do not allow children to tamper with the controls
or play with the product.
¥ Keep all packaging well away from children.
During Use
¥ This appliance is designed for domestic use only,
specifically for the storage of edible foodstuffs
only.
¥ Frozen food must NOT be re-frozen once it has
thawed out.
¥ Do not place carbonated or fizzy drinks in the
freezer.
¥ Do not remove items from the freezer if your
hands are damp/wet, as this could cause skin
abrasions or frost/freezer burns.
¥ Ice lollies can cause Ôfrost/freezer burnsÕ if
consumed straight from the freezer.
¥ ManufacturersÕ storage recommendations should
be strictly adhered to. Refer to relevant
instructions.
¥ The cooling plate or refrigerated freezer shelves
in this appliance contain channels through which
the refrigerant passes. If these are punctured this
will cause substantial damage to the appliance
and result in food loss. DO NOT USE SHARP
INSTRUMENTS to scrape off frost or ice. Under
NO circumstances should solid ice be forced off
the lining or shelves. Solid ice should be allowed
to thaw, when defrosting the appliance. See
Defrost Instructions.
Maintenance and Cleaning
¥ Switch off and unplug the appliance before
carrying out any cleaning or maintenance work.
Servicing
¥ This product should be serviced by an authorised
engineer and only genuine spare parts should be
used.
¥ Under no circumstances should you attempt to
repair the machine yourself. Repairs carried out
by inexperienced persons may cause injury or
serious malfunctioning. Refer to your local
Service Force Centre and always insist on
genuine spare parts.
At the end of the Appliance
Life
¥ When disposing of your appliance, use an
authorised disposal site.
¥ Remove the plug and ensure that any locks or
catches are removed, to prevent young children
being trapped inside.
19
Door reversal directions
Important
Before carrying out the operations described below
unplug the mains lead from the wall socket.
To carry out this reversal, proceed as follows:
1. Gently lay the fridge-freezer on its back with the top
held away from the floor by 5-8 cm (2-3 inches) of
packing.
2. Using a PHILLIPS screwdriver remove the top hinge.
3. Slide out the upper door from the middle hinge.
4. Unscrew the left levelling foot.
Unscrew the right levelling foot, hinge and refit them
on the left side.
Refit the other foot on the right side.
5. Slide out the lower door from the middle hinge.
6. Remove the middle hinge.
7. Remove the plastic plugs from the screw holes of the
new top & middle hinge location and refit them in the
holes on the opposite side.
8. Remove the screws from the new location of the
bottom hinge and refit them in the free holes on the
opposite side.
9. Refit the middle hinge as shown in Fig., i.e. up-side-
down with respect to the previous position.
10.Replace the lower & upper door making sure that the
pins of the middle hinge fit into the corresponding
bushing on the door.
11.Replace the bottom hinge on the left side of the
lower base of the cabinet (the fastening holes are
already provided). Refit the top hinge.
Important
The central hinge is designed to allow a certain amount
of side clearance (play), i.e. approx. 3 mm horizontally,
which makes it easy to line up the two doors by
proceeding as follows:
Loosen the two screws securing the hinge to the
cabinet.
Carefully position the hinge until the two doors are
perfectly aligned, then firmly screw down the hinge in its
new setting (position).
Reversing door handles
Remove the handle by unscrewing the two fastening
screws.
Remove the plastic plugs from the screw holes of the
new handle location and refit them in the free holes
onthe opposite side;
Refit the handle upside-down, on the opposite side of
the door.
Attention
After completion of the door reversing operation, check
that the door gasket adheres to the cabinet. If the
ambient temperature is cold (i.e. in Winter), the gasket
may not fit perfectly to the cabinet. In that case, wait for
the natural fitting of the gasket or accelerate this
process by heating up the part involved with a normal
hairdrier.
D053
PR132
PR184
D185
Printed on recyclated paper