_______________________________________________________________ TRIAX TSR 1000 ________________________________________________________________ Digital Satellite Receiver FTA User Guide
SAFETY PRECAUTION CAUTION: The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to "dangerous voltage" and to prevent from a risk of electric shock. Warning: To reduce the risk of electric shock, don't open the cabinet. Refer servicing to qualified personnel only. The exclamation point within an equilateral triangle is intended to alert the user to important operating and maintenance (servicing).
Locating: Slots and openings in the cabinet are provided for ventilation to protect it from overheating. Do not block these openings or allow them to be blocked by placing the STB on a bed, sofa or other similar surface, nor should it be placed over a radiator or heat register. Power-Cord Protection: Place the power-supply cord out of the way, where it will not be walked on. Please take special attentions to cords at plugs, convenience rece ptacles and the point where they exit from the unit.
Contents CONTENTS 1. Remote Control & Panel Description ....................................................... 3 1.1 Front Panel Description........................................................................... 3 1.2 Rear Panel Description ........................................................................... 4 1.3 Remote Control Description .................................................................... 5 2. Basic Operations..................................................................
Contents 3.5 Delete All ............................................................................................... 17 3.6 Restore channel list and settings............................................................. 17 3.7 Save channel list and settings ................................................................. 18 4. Installation ................................................................................................ 19 4.1 Antenna Setup..................................................
Remote Control & Panel Description 1. Remote Control & Panel Description 1.1 Front Panel Description 1. 2. 3. 4. 5. 6. 7. POWER: Is used to switch between the working mode and the standby mode. Display (4-Digit/7-Segment): Displays the received channel number while operating and time while in standby mode. Remote Sensor: Detects the infrared signals from the remote control unit. VOL+/-: To change volume to move cursor, change numbers in the menu or to change the choice.
Remote Control & Panel Description 1.2 Rear Panel Description 1. IF OUT: Satellite output for cascading to other devices Note: The operation of another receiver at the same time is only possible with limited channel selection. 2. IF IN: Satellite input. 3. RS-232: Serial Port allowing software upgrades. 4. ANT IN: Connect the antenna of TV to Aerial IN. 5. AC IN: Mains input cable. 6. POWER ON/OFF: Allows to completely switch off the receiver. 7. VIDEO / AUDIO: HiFi outputs for stereo set or monitor. 8.
Remote Control & Panel Description 1.
Basic Operations 2. Basic Operations 2.1 Switch on STB Switch the [Device’s Main Power] switch on. you will set Language, First Audio, Second Audio, LNB Power, Antenna Setup and Multi Search. ? Frequently Asked Question Q: The power of my STB is on and it is running in TV mode but the TV screen shows nothing: A: Make sure the TV set has been set to the correct video input(not the TV channels).
Basic Operations 2.5 Channel Number In TV/radio mode you can enter the channel number directly with your remote control unit and confirm the number with the OK button to change to the desired channel. 2.6 Mute 1. Press the [Mute] button to mute the sound. On the screen an icon will be displayed to indicate the muted sound. 2. Press the [Mute] button again to restore the sound. 2.7 Pause 1. In TV/radio mode, press the [Pause] button to stop the display. The sound of the channel will continue. 2.
Basic Operations 2.10 EDIT In TV mode, press the [EDIT] button to open the “TV Channel List” window. 2.11 Audio Track / Mode 1. In TV mode, press the [Audio] button to open the audio mode window. 2. Select the item you want to adjust with [Channel Up/Down] and change the value with [Volume Up/Down]. 2.12 INFO In TV mode, press [INFO] button can open information screen, in the window shows the parameters of current channel.
Basic Operations 2. The [Red] button opens the detailed schedule of the marked channel. You can select an event with [Channel Up/Down] and display the event’s detailed description with [OK]. 3. Press the [Green] button in the EPG menu to display the detailed information of the actual event in the selected channel. With the [Yellow] button you can program a timer with the start and finish time and date of this event. 4.
Basic Operations 3. 4. 5. 6. Press [Yellow] button to open the SAT list. After selecting a satellite the channel list will be reduced to the channels of this satellite. Press [FAV] button to open FAV list. After selecting a favorite group the channel list will be reduced to the channels of this group. Press [Blue] button to open the find window. You can use this feature to find channel by their names. Press [OK] to change and display the marked channel. 2.16 Change Satellite 1.
Basic Operations 2.19 SUB SUB(Subtitle): In “OSD Setting menu, use [Volume Up/Down] to select “On” or “Off”. If the current channel has subtitle information, it will be displayed if this function is “On”. If this function is “Off” subtitles won’t be displayed. 2.20 TXT 1. Press [TXT] button in TV mode to open the teletext page. This service is depending on the support of the channel provider. 2. If the channel does not support teletext information, it will show “No Teletext Data” on the screen. 2.
Menu Operations 3. Channel Press [Menu] in the TV/radio mode to enter the main menu. 1. Press [Channel Up/Down] to select the channel item. 2. Press [OK] to enter the selected item. In the channel menu: Press [Channel Up/Down] to select the wanted menu item among TV Channel List, Radio Channel List, Channel setup, Favorite channel list name, Delete All, Restore channel list and settings and Save channel list and settings. Press [OK] to enter the selected item. 3.
Menu Operations 3.1.1 Favorite 1. Press [FAV] to open the favorite window. 2. You can select between 8 favorite groups with [Channel Up/Down]. Press [OK] to assign the channel to a favorite group, press [EXIT] to exit favorite group. 3. Press [OK] again to remove the channel from the marked favorite group. 4. Press [MENU] button you will be asked “Are you sure to save?”. Select “Yes” to save the marked favorite group. Select “No” to cancel the operation. 5. To return to the TV channel list.
Menu Operations ¾ ¾ FTA: Sort channel by free and scrambled sequence. Free channels will be listed first and scrambled channels behind in the channel list. Lock: Unlocked channels are listed first end locked channels at the end. 3.1.4 TV Channel List Edit After pressing the [Yellow] button a window for entering the password will open. The default password is “0000”. You can Move, Skip, Lock and Rename the channel. Press [MENU] to leave the channel editing.
Menu Operations 1. Selecting the name item with [OK] will display a button pad to show you how to edit the channel name. 2. On the “Video PID”, “Audio PID” and “PCR PID” items you can input numbers to modify the item’s value. 3. After modification select “Save” and press [OK] button to save the modified values and exit “Edit” mode. Or select “Exit” and press [OK] to leave Edit mode without saving the modifications. Create Press [Green] button to open the Create window. 1.
Menu Operations 3.2 Radio Channel List Basically the operation of “Radio Channel List” is same as “TV Channel List”, except that in the small channel window the radio Logo will be displayed. 3.3 Channel Setup When you enter the “Channel Setup” menu you will see a screen like beside: 1. Startup Channel: Press [OK] to enter “Startup Channel” menu to see the screen like showed beside: ¾ If you set of “Boot on Channel” to “On” you can edit the following two items.
Menu Operations 3.4 Favorite channel list name When you enter “Favorite channel list name” menu with 8 favorite group will be displayed. Press [Red] or [OK] key on the RCU to rename favorite group with the [Number] buttons. After modification select “Save” and press [OK] to save the favorite group name and leave the edit mode. Select “Exit” and press [OK] to exit the edit mode without saving the favorite group name. 3.5 Delete All To delete all channels: 1. Enter the password.
Menu Operations 3.7 Save channel list and settings To save channel list and settings. 1. Enter the password. The default password is “0000”. 2. After entering the password correct a safety question will show up where you have to confirm first. 3. 3. Select “Yes”, press [OK] to save current channel list to backup channel list. Select “No” press [OK] to cancel the operation.
Menu Operations 4. Installation After selecting the installation menu you can see the window like beside. In “Installation” menu; 1. Press [Channel Up/Down] to select menu items among Antenna Setup, Single Search, Multi Search, TP Scan, Satellite List, TP List and Satellite Guide. 2. Press [OK] to enter the selected item. 4.1 Antenna Setup After selecting antenna setup another window will be opened. You can edit the following items: 1.
Menu Operations 3. 4. 5. 6. 7. 8. 2Cascades Port1 / 2Cascades Port2 / 2Cascades Port3 / 2Cascades Port4 / 2Cascades Port5 / 2Cascades Port6 / 2Cascades Port7 / 2Cascades Port8 / 2Cascades Port9 / 2Cascades Port10 / 2Cascades Port11 / 2Cascades Port12 / 2Cascades Port13 / 2Cascades Port14 / 2Cascades Port15 / 2Cascades Port16. Positioner: Press [Volume Up/Down] to select between “None / DiSEqC1.2 / USALS”. Toneburst: Press [Volume Up/Down] to switch this function “On” or “Off”.
Menu Operations 4.3 Multi Search When you enter the “Multi Search” menu a window like the one beside will open. 1. On “Satellite” item press [OK] to open the satellite list. Then press [Channel Up/Down] to move the highlight and press [OK] to mark/unmark and [MENU] to finish the selection. You can select several satellites in this menu. The system will use DiSEqC1.0/1.1, DiSEqC1.2 and USALS functions to search the marked satellites and scan channels. 2.
Menu Operations When you press [Green] a safety question will be displayed for confirmation to delete the current transponder or not. If you select “Yes”, the current transponder will be deleted and the total number of transponders will be reduced. For existing transponders you also can use number buttons to modify the parameters of “TP Frequency” and “Symbol Rate” or [Volume Up/Down] to change the value directly. “Polarity” and “FTA only” are used for setting scans conditions.
Menu Operations 2. Press [Green] button to open the “Add satellite” window. 3. After pressing [Yellow] button you will be asked “Are you sure to delete?”. Select “Yes” to delete the marked satellite. Select “No” to cancel the operation. 4.6 TP List When you open the “TP List” menu you will see a window like the one beside. 1. Press [Volume Up/Down] to change the marked satellite. 2. Press [Red] button to open the “Edit TP” menu. Here you can edit the transponder’s data.
Menu Operations 3. Press [Green] button to open the “Add TP” menu. Here you can add a new TP and setup its parameters. 4. Press [Yellow] button will open a dialog box asking you to confirm the deletion of the current TP. If you select “Yes” all the related channels will be deleted. If you select “No” the operation will be cancelled. 5. Pressing the [Blue] button will open a dialog box asking you to confirm the deletion of all TP on current satellite.
Menu Operations 1. 2. 3. 4. 5. Use the [Number] buttons to input the values of “Local Longitude”, “Local Latitude” and “Satellite Longitude”. Press [Volume Up/Down] to switch east or west in “Local Longitude” and “Satellite Longitude” or to switch north or south in “Local Latitude”. Highlight the “Start” item and press [OK]. In the lower part of the window the corresponding values for the antenna setting is displayed. Orientation means the angle between south and satellite.
Menu Operations 5. System Setup When you open the “System Setup” menu a window like the one beside will be opened. In “System Setup” menu: 1. Press [Channel Up/Down] to select menu items among Language, TV System, Time & Timer setting, OSD Setting, Parental Lock, LNB Power and RCU position switch. 2. Press [OK] to open the selected item. 5.1 Language After selecting the “Language” menu you will see a window like beside: 1. Language: Press [Volume Up/Down] to select languages.
Menu Operations 5.2 TV System When you enter the “TV System” menu you will see the screen like below: 1. Display Mode is used to switch the display mode. You can select from Auto / PAL / PAL-N / PAL-M / NTSC3.58. Press [Volume Up/Down] to switch the desired mode. 2. Aspect Mode is used to switch the screen aspect ratio mode. You can select from Auto / 4:3 PS / 4:3 LB / 16:9. Press [Volume Up/Down] to select the needed mode. 3. Video output is use for switching the screen aspect ratio mode.
Menu Operations NOTE: If the current channel provides the correct time information, you will see the current time after you entered “Time” menu. If the channel doesn’t provide time information, you have to input the date and time information manually. The most channels support the time signal. ¾ Press [MENU] to leave the “Time” menu. Timer: Select “Timer” item and press [OK] to enter the “Timer list” menu. You can press [Channel Up/Down] to select a timer. Then press [OK] to open the related timer menu.
Menu Operations When you select “Message”(reminding message) option in “Timer Service” then you can enter additional data: ♦ Wakeup Message: Press [Volume Up/Down] to select the category of the reminding message from Birthday, Anniversary and General. ♦ Wakeup Date: Use the [Number] buttons to input your wakeup date. ♦ On Time: Use the [Number] buttons to input your wakeup time.
Menu Operations 5.5 Parental Lock You can set a password for anyone who wishes to operate the “Installation” menu. You can also set the password to lock channels. Below you find how to set and change the password. 1. On “Parental Lock” press [OK] to open a dialogue box and input the password. After you entered the correct password, you will see a screen like beside: 2. Menu Lock: If Menu Lock is set to “Yes” then you need to enter the password every time you want to open the menu.
Menu Operations 5.7 RCU position switch 1. This item can select the switch controller’s position. The position number you choose in this menu must be same as the switch controller’s setup, or the switch controller can not work correctly. 2. Press [◄/►] to modify the change.
Menu Operations 6. Tools When you enter to “Tools” menu, you will see a screen like beside: In “Tools” menu: 1. Press [Channel Up/Down] to select the wanted item among Information, Quick Setup, Game, Factory Default, Software Upgrade and SatcoDX Auto Programming. 2. Press [OK] button to enter the selected item. 6.1 Information 1. When you select the “Information” menu you will see a screen like beside. The screen displays data about the current channel. 2.
Menu Operations Basic operation statement: 1. Tetris ¾ Mark “Setup” and press [Volume Up/Down] to select the level (speed). ¾ Mark “Start” and press [OK] to start the game. ¾ Mark “Cancel” and press [OK] to leave the game. ¾ Play the game: ♦ Press [Volume Up/Down] to move the block left or right ♦ Press [Channel Up] to rotate the block clockwise ♦ Press [Channel Down] to drop the block faster ♦ Press [OK] to Pause/Play the game ♦ Press [MENU] to leave the game and return to the game menu. 2.
Menu Operations ♦ ♦ ♦ Press [Volume Up/Down / Channel Up/Down] to position the round mark. Press [OK] to set your stone. Press [MENU] to quit the game and return to the game menu. 6.4 Factory Default When you press [OK] on the “Factory Default” item: 1. A dialogue box will occur where you need to enter the password. 2. After you input the correct password a warning message will be displayed like the one beside. 3. If you select “Yes” then all changes you made will be reset to default values.
Menu Operations Update Software(receiver to receiver) 1. Connect master and slave receivers with twisted RS-232C cable. 2. Power on the master receiver and make it in standby mode input number key. 3. Turn on slave receiver to begin update. 4. Input the password “123” by remote control to update the software. 5. After update, it will display “-End” on slave panel. 6. Turn off slave receiver, disconnect twisted RS-232C cable and restart it. Notes: Input the password “123” to update the software.
Menu Operations b) RS232 CABLE LAYOUT # CONNECT TO P.C # CONNECT TO SVR c) Among wires from no.1 to 9 connect wire no.2 and 3 crossed to both sides, and then connect the GROUND(GND) of terminal on P.C to SVR, and then cut other wires. Upgrade by Satellite This function can upgrade the software of your receiver through data sent by a satellite. At the moment we offer satellite updates only through ASTRA1 and Hotbird satellites. 1. Select the satellite and TP or input the TP value and download PID. 2.
Menu Operations 6.6 SatcoDX Auto Programming This function is using the tables of the SatcoDX websites to update your channel and satellite lists. You need a special application which is available on the CD-ROM of the Tele-Satellite magazine. Install this software on your PC first. 1. Start the SatcoDX application on your PC. 2. Select “SatcoDX Auto Programming” item from the “Tools” menu and press [OK]. The screen will show the message “OK to Proceed”. 3.
Technical specification 7.
Technical specification MISCELLANEOUS Supply voltage Power consumption Operation temperature Storage temperature Dimension (W x D x H) Weight 100~240VAC 50/60Hz 30 watts max +5 °C to +40 °C -20 °C to +70 °C 39
