Owner manual

IDWH Sensor Parameters
12
 %(%#$
H (-@1> @19<1>-@A>1? ;B1> G /-: /-A?1
?1B1>1.A>:?5:?@-:@8E;>01-@42>;9?/-805:3
H 4580>1: 05?-.81 -:0 1801>8E ->1 -@ 45341?@
>5?7;2.15:3?/-80
H 1B1>81-B1@419A:-@@1:0105:;>:1->?4;C
1>.-@4@A.;>?5:7
H 1B1>-88;C?9-88/4580>1:@;A?1-4;@C-@1>
2-A/1@;>0>-C@415>;C:.-@4
H 2 -:E;:1 A?5:3 4;@ C-@1> 5: @41 .A5805:3 25@?
@41-.;B101?/>5<@5;:;>528;/-8/;01?;>?@-@1
8-C? >1=A5>1 ?<1/525/ C-@1> @19<1>-@A>1? -@
4;@C-@1>2-A/1@5@5?>1/;991:010
 %; 5:?@-88 - @41>9;?@-@5/ 95D5:3 B-8B1 -@
@45?A:5@;>-@1-/4C-@1>2-A/1@
 %;?1@@41@19<1>-@A>1?1@@5:32;>@418;C
1?@ @19<1>-@A>1 C45/4 ?-@5?251? E;A> 4;@
C-@1>:110?
H (-@1> 0>-5:10 2>;9 @41 ?E?@19 0>-5: B-8B1?
9-E.11D@>1918E4;@%;-B;505:6A>E
 -71?A>1-88/;::1/@5;:?->1@534@
 5>1/@C-@1>28;C-C-E2>;9-:E<1>?;:
DANGER
($$ #!#%#
1
. Once the access code number has been stored and
accepted in the control module, change the display
readout to “Parameter” mode by pressing MODE
until the display shows
PARA.
2. Press STEP to enter the first parameter setting.
Continue pressing STEP until the display shows
P_46.
E <>1??5:3 $%! E;A C588 ?1=A1:/1 @4>;A34 @41
<->-91@1>?1@@5:3?-?2;88;C?11402_013_01
4186P_10P_11P_12P_46%4105?<8-E
>1-0;A@ C588 /;:@5:A1 ?4;C5:3 JPK 2;88;C10 .E - 
0535@:A9.1>@4-@5:/>1-?1? -2@1>1-/4<>1??;2 @41
$%!.A@@;:-2@1>@412;A>@4<->-91@1>?1@@5:3
%41<->-91@1> ?1@@5:3C588/;:@5:A1 2;> 05221>1:@
<->-91@1>?1@@5:3E/;:@5:A5:3@;<>1??@41$%!
.A@@;: @4105?<8-E >1-0;A@ C588 >;88;B1> @;@41 25>?@
<->-91@1>?1@@5:3
3. When the display readout shows P_46, stop press-
ing the STEP button. Wait a second and the display
will flip over to the current setting of parameter 35 in
the right two digits of the display.
4. Press the + or - button to revise the setting until the
display shows
_12.
5. Press the STORE button to save the change. The
display will flash once to indicate the control module
accepts the change.
NOTICE
NOTICE