Owner manual

Program Access of the MCBA Control
!# #$$ %
 %# 
%412-/@;>E012-A8@?1@@5:32;>@41!#$%;:@>;8
;0A81@;;<1>-@1@41(5?@4>;A34-:-=A-?@-@
/;:@>;8%41!#$%;:@>;8;0A819A?@.1<>;
3>-9910-?01?/>5.105:@412;88;C5:35:?@>A/@5;:@;
/;>>1/@8E;<1>-@1@41(@4>;A34@41(?1:?;>
To adjust the factory parameter settings of the PRES-
TIGE MCBA Control, the installer must enter into the
parameter menu of the control.
;:;@-@@19<@@;>1B5?1-:E;@41>/;:@>;8<->-91@1>
?1@@5:3? 1D/1<@ @4;?1 85?@10 5: @45? ?A<<8191:@
!1>2;>9;:8E@4;?1<->-91@1>>1B5?5;:?01?/>5.105:
@45??A<<8191:@  -58A>1@; /;9<8E/;A80 >1?A8@ 5:
1>>-@5/ ;> A:>185-.81 ;<1>-@5;: ;2 @41 !#$%
>1?A8@5:3 5: ?1B1>1 <1>?;:-8 5:6A>E 01-@4 ;> ?A.
?@-:@5-8<>;<1>@E0-9-31
;> -005@5;:-8 5:2;>9-@5;: ;: >1B5?5:3 @41 !#$
%  ;:@>;8 ;0A81 ;<1>-@5;:-8 <->-91@1>
?1@@5:3? >121>1:/1 @41 !#$% ;:@>;8
$A<<8191:@
%'%%$$ 
To enter the parameter listing of the MCBA control, the
installer must enter the activation code as follows:
1. Press and hold the MODE button
2. Continue holding the MODE and press STEP button
until
STBY appears and hold both STEP and MODE
buttons for 2 to 3 seconds.
The display should read
CODE
3. Release the STEP and MODE buttons on the control
panel.
4. Press STEP once.
NOTICE
WARNING
NOTICE
The display should read C_ XX (XX should be
a random number from 00 to 99)
5. Press the + or - button to change the display num-
ber C_ XX to read C_54. Press and release the +
or - to change the display one number at a time.
Press and hold the + or - to rapidly change the dis-
play number.
6. When the display reads C_54 press STORE to
save the activation code. The display C_54 should
flash when the code is entered and saved.
After the activation code is entered press the MODE but-
ton until the display shows PARA. At this point the
installer can access the parameters required for applica-
tion.
Once in the parameter mode, press the STEP repeated-
ly to reach the appropriate parameter setting. The dis-
play should show the following sequence, as the STEP
button is press repeatedly:
Press STEP once- 1140
Press STEP x2 - 2_01
Press STEP x3 - 3_01
Press STEP x4 - 4186
Press STEP x5 - P_10
Press STEP x6 - P_11
Etc......
After Parameter 4 the display will continue to show P fol-
lowed by a two-digit number that increases with each
press of the STEP button.
%41 -/@A-8 <->-91@1> B-8A1? 05?<8-E10 ;: @41
A:5@9-EB->E01<1:05:3;:@41-<<85/-@5;:%41
<->-91@1> ?1=A1:/1 C588 -8C-E? ;//A> 5: @41
;>01>?4;C:
NOTICE
10