Manual

ManualsBrandsTriangle Tube ManualsBoilers76,000 BTU Output Prestige Solo 110 Condensing Gas Boiler w/ TriMax Control (LP)

WARNING

2008-04 Prestige Concentric Vent/Air Term.

"01;,7+=5-6<1;16<-6,-,<7*-=;-,*A)9=)41.1-,0-)<16/+76<:)+<7:7:;-:>1+-

<-+061+1)6 -),)4416;<:=+<176;?1<016<01;,7+=5-6<)6,?1<016<0- !"

714-:6;<)44)<176)6,)16<-6)6+-)6=)4*-.7:-8:7+--,16/?1<0<0-16;<)44)

<176<1;:-+755-6,-,<7.7447?<0-8:7+-,=:-;16<0-;<-8;/1>-6;318816/7:

51;;16/ 8:7+-,=:)4 ;<-8; +7=4, :-;=4< 16 ;->-:- 8-:;76)4 162=:A ,-)<0 7: ;=*

;<)6<1)48:78-:<A,)5)/-

6;<)44)<176 7. <01; *714-: 5=;< +7584A ?1<0 47+)4 :-9=1:-5-6<; )6, +7,-; )6,

?1<0<0-)<176)4=-4);7,-!(.7:16;<)44)<176;?1<016<0-

#!7:16;<)44)<176;16)6),)<0-16;<)44)<1765=;<+7584A?1<0!7:



NOTICE

prestige

PVC Concentric Vent/Air

Termination Supplement

Revised 06/8/09

Summary of content (16 pages)

PAGE 1
prestige PVC Concentric Vent/Air Termination Supplement LI STED WARNING This document is intended to be used by a qualified heating contractor or service technician. Read all instructions within this document and within the PRESTIGE Boiler Installation and Maintenance Manual, before proceeding with the installation. It is recommended to follow the procedures in the steps given, skipping or missing procedural steps could result in severe personal injury, death or substantial property damage.
PAGE 2
Table of Contents PRODUCT AND SAFETY INFORMATION Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Installer Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Homeowner Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 SECTION I - PRE-INSTALLATION ITEMS Removal of an Existing Boiler from a Common Vent System . . . . . .
PAGE 3
Product and Safety Information DEFINITIONS The following terms are used throughout this manual to bring attention to the presence of potential hazards or to important information concerning the product. CAUTION Indicates a potentially hazardous situation which, if ignored, may result in minor injury or substantial property damage. DANGER Indicates the presence of a hazardous situation which, if ignored, will result in death, serious injury or substantial property damage.
PAGE 4
Pre-Installation Items 4. Place in operation the appliance being inspected. Follow the lighting instructions. Adjust thermostat so appliance will operate continuously. SECTION I - PRE- INSTALLATION ITEMS Removal of an Existing Boiler from a Common Vent System 5. Test for spillage at the draft hood relief opening after 5 minutes of main burner operation. Use the flame of a match or candle, or smoke from a cigarette, cigar or pipe.
PAGE 5
Pre-Installation Items Vent/Combustion Air Piping and Materials NOTICE For installations in Canada, all piping, fittings and cement/primer material must be certified and listed to ULC-S636. NOTICE Installation of the vent and combustion air piping must comply with local codes and requirements and with the National Fuel Gas Code NFPA 54, ANSI Z223.1 for installations in the U.S. or with CSA B149.1 or B149.2 for installations in Canada. NOTICE Do not use cellular core pipe for venting.
PAGE 6
Pre-Installation Items Combustion Air Contamination Potential contaminating products WARNING On a concentrically vented PRESTIGE the combustion air must be piped directly from the outdoors to the boiler. If the combustion air inlet is located in any area likely to cause or contain contamination, or if products, which would contaminate the air cannot be removed, the combustion air must be repiped and terminated to another location.
PAGE 7
Installing Vent Termination Kit SECTION II - INSTALLING VENT TERMINATION KIT b. The flue products will form a noticeable plume as they condense in colder air. Avoid terminating the vent in areas where the plume could obstruct window views. Vertical - Through the Roof c. NOTICE Installation of the vent and combustion air piping must comply with local codes and requirements and with the National Fuel Gas Code NFPA 54, ANSI Z223.1 for installations in the U.S. or CSA B149.1 or B149.
PAGE 8
Installing Vent Termination Kit 5. The vent termination must also maintain the following clearances; as shown in Fig.6, page 10. Termination Assembly Support 1. If assembly needs to be extended to meet height requirements the two pipes supplied in the kit may be replaced using the same diameter, solid, single PVC pipe. a. At least 3 feet from adjacent walls b. No closer than 3 feet below roof over hangs c. At least 7 feet above any public walkways WARNING d.
PAGE 9
Installing Vent Termination Kit Multiple Installation - Through the Roof WARNING 1. On installations of multiple PRESTIGE boilers, install the concentric vent/air termination assemblies as described in this manual. All vent outlets of the termination assemblies must be of the same height to avoid flue gas recirculation and the possibility of severe personal injury, death or substantial property damage. 2.
PAGE 10
Installing Vent Termination Kit 3. The vent and combustion air piping connected to the concentric vent/air termination assembly must comply with the instructions listed in this supplement. Horizontal - Sidewall NOTICE WARNING Installation of the vent and combustion air piping must comply with local codes and requirements and with the National Fuel Gas Code NFPA 54, ANSI Z223.1 for installations in the U.S. or CSA B149.1 or B149.2 for installations in Canada.
PAGE 11
Installing Vent Termination Kit d. Avoid locations where prevailing winds could affect the performance of the boiler or cause recirculation of the flue gases, such as inside corners of buildings or near adjacent buildings or vertical surfaces, window wells, stairwells, alcoves, courtyards, or other recessed areas. Vent Installation - Sidewall 1. Sidewall Penetration - 2. The installer must comply with all local codes for isolating the vent pipe as it passes through floors and walls. e.
PAGE 12
Installing Vent Termination Kit Termination Assembly Support Multiple Installation - Sidewall 1. If assembly needs to be extended to meet wall thickness requirements the two pipes supplied in the kit may be replaced using the same diameter, solid, single PVC pipe. 1. On installations of multiple PRESTIGE boilers, install the concentric vent/air termination assemblies as described in this manual. 2.
PAGE 13
Installing Vent Termination Kit 1. Reference Fig.1 page 3 for component part description and dimensional information. 2. Install factory supplied bird screen between end of vent pipe and vent cap. 3. Begin partial assembly of the termination components in the sequence as shown in Fig. 7 thru Fig. 7B. - DO NOT install the vent cap with the bird screen until the assembly has been inserted through the roof or sidewall penetration and all support bracing has been installed. 4.
PAGE 14
Installing Vent Termination Kit • The 4” vent system may transition back to a 3” vent system within 5 feet of the concentric vent termination. This transition may occur in a vertical or horizontal run. • The total equivalent length of the 3” vent and 4” vent combined shall not exceed the length listed for a 4” vent system Table 1, page 13. Insert Piping to PRESTIGE Adapters 1. The installer must clean, deburr and chamfer the outside of the pipe ends.
PAGE 15
Installing Vent Termination Kit 2. The installer should cut the pipe to the required lengths and deburr the inside and outside of both ends. 8. The vent and combustion air piping should be sloped continuously from the termination back to the boiler with at least 1/4 inch drop per foot of run. Do not allow any sags in the run of piping. 3. The installer should chamfer the outside of the pipe ends to allow even distribution of cement when joining. WARNING 4.
PAGE 16
Additional quality water heating equipment available from Triangle Tube/Phase III PRIMARY / SECONDARY MANIFOLD - Combination hydronic separator, pressure equalizer and distribution manifold - Ensures a proper primary/secondary piping arrangement for up to three zones - Easy to install and compact SMART INDIRECT FIRED wATER HEATERS - Exclusive tank-in-tank design - Stainless steel construction - Available in 8 sizes and 2 models - Limited LIFETIME residential warranty - 15 year limited comme