PVC/CPVC Sidewall Vent Termination Kit Instructions

ManualsBrandsTriangle Tube ManualsCommercial Water Heaters3" PVC Sidewall Termination

PVC/CPVC Low Profile Sidewall

Vent Termination Kit

Kit Part Number:

PSVTERM03

2 Inch PVC/CPVC Vent Sidewall Termination

PSVTERM04

3 Inch PVC/CPVC Vent Sidewall Termination

PSVTERM05

4 Inch PVC/CPVC Vent Sidewall Termination

Recommended tools:

• Phillips Screwdriver

• Core Drill or Hole Saw

Failure to follow instructions below can result

in severe personal injury or damage if ignored.

• Instructions are for a qualified installer/ser-

vice technician.

• Read all instructions before proceeding.

• Follow instructions in proper order.

The sidewall vent termination is certified to

ULC S636 standard.

This vent termination must be installed in

accordance with all applicable local, state,

national and provincial codes, ordinances,

regulations and laws.

WARNING

NOTICE

Indicates a potentially hazardous situation

which, if ignored, can result in serious

injury or substantial property damage.

Indicates special instructions on installa-

tion, operation or maintenance, which are

important to equipment but not related to

personal injury hazards.

WARNING

NOTICE

Termination

plate

Wall Plate

Fig. 1: PVC/CPVC Sidewall Vent Termination

Summary of content (4 pages)

PAGE 1
PVC/CPVC Low Profile Sidewall Vent Termination Kit Kit Part Number: Wall Plate PSVTERM03 Termination plate 2 Inch PVC/CPVC Vent Sidewall Termination PSVTERM04 3 Inch PVC/CPVC Vent Sidewall Termination PSVTERM05 4 Inch PVC/CPVC Vent Sidewall Termination Recommended tools: • • Phillips Screwdriver Core Drill or Hole Saw Fig. 1: PVC/CPVC Sidewall Vent Termination NOTICE WARNING Indicates a potentially hazardous situation which, if ignored, can result in serious injury or substantial property damage.
PAGE 2
PVC/CPVC Low Profile Sidewall Vent Termination Kit Pre-Installation Guidelines NOTICE 1. The vent termination location must maintain all termination clearances stated in Section II Direct Vent Installation of the Vent Supplement included with the boiler. For installations in Canada, all piping, fittings and cement/primer material must comply with ULC S636 certification. 2. Ensure vent termination location does not exceed the maximum allowable vent length as listed in the boiler Vent Supplement.
PAGE 3
PVC/CPVC Low Profile Sidewall Vent Termination Kit 6. When assembling the wall plate to the vent and air pipes the installer should: Table 1 Vent Pipe Hole Size Air Pipe Hole Size 2” PVC/CPVC 4” 2 3/8” 3” PVC/CPVC 4” 3.5” 4” PVC/CPVC 5” 4.5” Pipe Size a. Handle the wall plate and pipes carefully to prevent contamination of surfaces. b. Apply a liberal amount of primer to the end of the pipes and the wall plate sockets. c. Apply a light uniform coating of approved cement to both surfaces.
PAGE 4
PVC/CPVC Low Profile Sidewall Vent Termination Kit 3.75” 14.25” 1.25” 13.50” 5.63” 2. 81” 7.88” 8. 63” Wall Thickness Varies Fig. 3: Vent Termination Dimensions Vent Size “A” Dimension 2 Inch 14.50 3” Inch 15.50 4” Inch 16.50 12” Minimum to grade or snow line Fig. 4: Vent Termination Dimensions “A” Dimension Minimum Fig. 5: Multiple Vent Termination - Vertical Vent Size “A” Dimension 2 Inch 14.50 3” Inch 15.50 4” Inch 16.50 “A” Dimension Minimum Fig.