Prestige Stainless Steel Vent Termination Kit Instructions

ManualsBrandsTriangle Tube ManualsBoilers4" - Sidewall Vent Termination Kit - Stainless Steel

Prestige Gas Vent Stainless

Termination Kit

Kit Part Number:

PSVKIT01

3 Inch Vent System Termination

PSVKIT02

4 Inch Vent System Termination

Recommended tools:

• Phillips Screwdriver

• Core Drill or Hole Saw

Failure to follow instructions below can result

in severe personal injury or damage if ignored.

• Instructions are for a qualified installer/ser-

vice technician.

• Read all instructions before proceeding.

• Follow instructions in proper order.

WARNING

Indicates a potentially hazardous situation

which, if ignored, can result in serious

injury or substantial property damage.

Indicates special instructions on installa-

tion, operation or maintenance, which are

important to equipment but not related to

personal injury hazards.

NOTICEWARNING

Interior

late

Termination

Face Plate

Termination

Screening

xterior

Black Plate

Fig. 1: Prestige Gas Vent Termination Assembly

Summary of content (7 pages)

PAGE 1
Prestige Gas Vent Stainless Termination Kit Kit Part Number: PSVKIT01 3 Inch Vent System Termination PSVKIT02 4 Inch Vent System Termination Termination Screening Exterior Black Plate Interior Plate Termination Face Plate Recommended tools: • • Phillips Screwdriver Core Drill or Hole Saw Fig. 1: Prestige Gas Vent Termination Assembly WARNING NOTICE Indicates a potentially hazardous situation which, if ignored, can result in serious injury or substantial property damage.
PAGE 2
Prestige Gas Vent Stainless Termination Kit Pre-Installation Guidelines 4. All vent piping and assembly / gluing of the vent piping should comply with the guidelines referenced in the Prestige Vent Supplement. 1. The vent termination location must maintain all termination clearances stated in Section II Direct Vent of the Prestige Vent Supplement included with the boiler. 5.
PAGE 3
Prestige Gas Vent Stainless Termination Kit 10. Using the mounting screws removed in STEP 1, secure the termination faceplate to the exterior back plate. the support bands on the interior plate to support the piping. See Figure 2 and Figure 3. 6. Mount the exterior back plate over the protruding vent and air intake piping. Use the supplied #10 x 1” mounting screws to secure the plate to the exterior face of the building as shown in Figure 3. Mounting Screw Location (4 places Type) Interior Plate 7.
PAGE 4
Prestige Gas Vent Stainless Termination Kit Exterior Back Plate Termination Face Plate Vent Coupling Apply Bead of High Temp Silicone (RTV) Along Inside Surface Termination Screening Termination Face Plate Fig. 4: Exterior Assembly of Termination 12” Min. 12” Min. 3 1/2” (TYP) Maintain Vent Center Line 12 1/2” 32 1/2” Fig.
PAGE 5
Prestige Gas Vent Stainless Termination Kit 12” Min. 12” Min. 3 1/8” (TYP) Maintain Vent Center Line 15 1/2” 34 3/4” Fig. 5B: Multiple Vertical Vent Installation 4 Inch Venting System 47 3/4” 17 5/8” 12” Min. 12” Min. Exhaust 5 1/8” (TYP) Exhaust Fig.
PAGE 6
Prestige Gas Vent Stainless Termination Kit 53 3/8” 19 1/8” 12” Min. 12” 4” (TYP) Exhaust Exhaust Exhaust Fig. 6B: Multiple Vertical Vent Installation 4 Inch Venting System Wall Thickness Various 12 3/4” 3 3/4” 8 3/4” 5 1/2” Vent Outlet 2 1/4” 34 3/4” Fig. 7B: 3 Inch Vent Termination Dimensions Fig.
PAGE 7
Prestige Gas Vent Stainless Termination Kit Wall Thickness Various 15 1/2” 4 1/4” 9 3/4” 7” Vent Outlet 2 3/4” Fig. 8B: 4 Inch Vent Termination Dimensions Fig.