Prestige Indirect Fired Water Heater Sensor Application Supplement

15
$  !
1. Once the access code number has been stored and
accepted in the control module, change the display
r
eadout to “Parameter” mode by pressing MODE
u
ntil the display shows
PARA.
2. Press STEP to enter the first parameter setting.
Continue pressing STEP until the display shows
P_46 .
A 8:-;;16/ ! A7= ?144 ;-9=-6+- <0:7=/0 <0-
8):)5-<-:;-<<16/;);.7447?;11402_013_01
4186P_10P_11P_012P_46 !0-,1;
84)A:-),7=<?144+76<16=-;07?16/CPD.7447?-,*A
),1/1< 6=5*-:<0)< 16+:-);-;).<-:-)+0 8:-;;7.
<0- !*=<<76).<-:<0-.7=:<08):)5-<-:;-<<16/
!0-8):)5-<-: ;-<<16/?144 +76<16=-.7: ,1..-:-6<
8):)5-<-:;-<<16/A+76<16=16/<78:-;;<0- !
*=<<76 <0- ,1;84)A :-),7=< ?144 :7447>-: <7 <0- .1:;<
8):)5-<-:;-<<16/
767<)<<-58<<7:->1;-)6A7<0-:+76<:748):)5-<-:
;-<<16/ -@+-8< <07;- 41;<-, 16 <01; ;=884-5-6<
-:.7:5764A<07;-8):)5-<-::->1;176;,-;+:1*-,16
<01;;=884-5-6< )14=:- <7 +7584A+7=4,:-;=4< 16
-::)<1+7:=6:-41)*4-78-:)<1767.<0-:-;<1/-:-;=4<
16/ 16 ;->-:- 8-:;76)4 162=:A ,-)<0 7: ;=*;<)6<1)4
8:78-:<A,)5)/-
3. When the display readout shows
P_46, stop press-
ing the STEP button. Wait a second and the display
will flip over to the current setting of parameter 46 in
the right two digits of the display.
4. Press the + or - button to revise the setting until the
display shows
_12.
5. Press the STORE button to save the change. The
display will flash once to indicate the control module
accepts the change.
WARNING
NOTICE
NOTICE
):)5-<-:  0); ;->-:)4 7<0-: 87;;1*4- ;-<<16/;
)>)14)*4-!0-.)+<7:A;-<<16/7.<0-$1;)9=);
<)<+76<:747:
_13!0-:-9=1:-,:->1;-,;-<<16/7.
<0-$!+76<:747:
_126A7<0-:;-<<16/7.
8):)5-<-:  +7=4, :-;=4< 16 -::)<1+ 7: =6:-41)*4-
78-:)<1767.<0-:-;<1/-:-;=4<16/16;->-:-8-:;76
)4162=:A,-)<07:;=*;<)6<1)48:78-:<A,)5)/-
6. To exit the Code mode, press the RESET button
once. The unit will go into a self-check mode upon
acceptance of the reset.
$ !!!" !!
The parameter setting for the domestic storage temper-
ature set point is Parameter 1 and is accessible without
having to enter the access code.
To revise the parameter setting within the Prestige
Control Module for the set point of the Domestic Storage
temperature, the installer can access the parameter set-
ting by entering the Parameter Mode PARA during nor-
mal operation, the access code is not required.
1. Press MODE once until the display shows PARA.
2. Press STEP until the display shows 1140 or 1XXX
(where XXX is a setting other than the factory setting).
3. Press the + or - button until the desired DHW stor-
age temperature setting is achieved. Press STORE
to save the setting. The display will flash when the
revised setting is accepted.
WARNING