Blue t oot h car k it Use r ’ s Manual (Cover sheet, do NOT print) User’ s Manual Draft 3_b May 13, 2003
Pre fa c e This publication, including all photographs, illustrations and software, is protected under international copyright laws, with all rights reserved. Neither this manual, nor any of the material contained herein, may be reproduced without the express written consent of the manufacturer. Version 1.0, May, 2003 Trademarks Sony-Ericsson is a trademark of the Sony-Ericsson Corporation. Nokia is a trademark of the Nokia Corporation. Siemens is a trademark of the Siemens Corportation.
Preface N ot ic e s Fede ral Communications Commission (FCC) Statement Note: This equipment has been tested and found to comply with the limits for a Class B digital device, following Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Preface T a ble of Cont e nt s CHAPTER 1 Introduction Product overview and features Identifying components CHAPTER 2 Getting started Nokia mobile phones setup 1 1 1 2 3 3 3 Establishing a wireless connection.....................................................................3 Disconnecting the phone ...................................................................................4 Re-connecting the phone ...................................................................................
Chapte r 1 Introduction Congratulations on your new purchase! The Bluetooth Wireless Car Kit will help make your driving experience more convenient and provide you with years of trouble free use. Product overview and features The Car Kit is designed to make driving your car and talking on the phone safe and easy. It consists of a receiver, a four-button mountable control module, a multidirectional microphone, and a speaker.
Bluetooth Car Kit user’s manual Identifying components Speaker Control Module Microphone Junction Box Radio + RR Speaker + RR + LR + LR + LF + LF + RF + RF ISO Connector 2 Power Power out in Power Cable
Chapte r 2 Getting started The Bluetooth Car Kit is designed to function with many brands of mobile phones including Nokia, Siemens and Sony-Ericsson. The Car Kit can only operate with one phone at a time. If you wish to switch phones, it is necessary to reset the Car Kit, and establish a new connection. (Refer to “Resetting the Car Kit”.) Nokia mobile phones setup This section describes setting up and using the Car Kit with a Nokia phone.
Bluetooth Car Kit user’s manual 6. An Enter passcode prompt is displayed. Enter the factory default passcode “1234”, and press Select. The Car Kit settings are stored in the phone’s memory. Even when disconnected, the telephone stores the settings making re-connection automatic. Disconnecting the phone The phone automatically disconnects when you are outside the 10-meter range of the junction box. To manually disconnect the phone, follow one of the methods below. Method 1: 1.
Chapter 2—錯誤! 尚未定義樣式。 You only need to re-connect the phone if you manually disconnect it. Refer to the following to re-connect the phone: 1. Turn on the car ignition, then turn on the phone. 2. Scroll through the Menu and select Bluetooth. 3. Select View paired devices. 4. Select Triamp and press Options. 5. Scroll to Establish Bluetooth connection, and press Select. Connected to Triamp appears on the screen.
Bluetooth Car Kit user’s manual The Car Kit is operated using the following four-button control module: Answer/Disconnect Volume down Volume Up LED indicator light Redial/Voice Recognition Control Module Functions Answer/Disconnect Press to answer a call. Press again to hang up. Volume Down Press during operation to lower the volume. Volume Up Press during operation to increase the volume. Redial/Voice Recognition Press once to re-dial the last number called.
Chapter 2—錯誤! 尚未定義樣式。 LED indicator light The LED is on when a phone is connected to the Car Kit. Resetting the Car Kit When changing phones it is necessary to reset the Car Kit and establish a new connection. Refer to the following: 1. Press and hold the Volume Down button. 2. With the Volume Down button pressed, press the Answer/Disconnect button. The LED will turn off. The Car Kit is now reset. Important! To ensure a successful reset, do not turn off your car ignition while resetting the Car Kit.
Bluetooth Car Kit user’s manual Notes on using voice recognition Voice recognition is a feature of your phone which enables you to dial a number by saying a pre-recorded “voice tag”. Normally when you set a voice tag, you speak directly into the phone. When accessing this feature with the Car Kit, you may find it necessary to re-record the voice tag while you are in the car. This will set not only the way you say the voice tag, but also record a familiar background noise.
Chapter 2—錯誤! 尚未定義樣式。 Sony-Ericsson mobile phones setup This section describes setting up and using the Car Kit with a Sony-Ericsson phone. Establishing a wireless connection Refer to the following to establish a wireless connection between your phone and the Car Kit. (Details on changing your phone’s settings are provided in the user’s manual that came with your phone.) 1. Turn on the car ignition, then turn on the phone. 2. Scroll through the Menu and select Connect. Press Yes. 3.
Bluetooth Car Kit user’s manual 13. The Triamp name appears on your screen. To exit this screen without changing the nametag, press No. The Car Kit settings are stored in the phone’s memory. Even when disconnected, the telephone stores the settings making re-connection automatic. Disconnecting the phone The phone automatically disconnects when you are outside the 10-meter range of the junction box. To manually disconnect your Sony-Ericsson phone, follow the procedure below. 1.
Chapter 2—錯誤! 尚未定義樣式。 Using the control module The Car Kit is operated using the following four-button control module: Answer/Disconnect Volume down Volume Up LED indicator light Redial/Voice Recognition Control Module Functions Answer/Disconnect Press to answer a call. Press again to hang up. Volume Down Press during operation to lower the volume. Volume Up Press during operation to increase the volume.
Bluetooth Car Kit user’s manual Redial/Voice Recognition There is no redial function for Sony-Ericsson users. Pressing this button once will activate communication between the phone and the Car Kit. Your car stereo will mute and the LED will turn on, but there will be no phone call placed. To turn off the communication between the Car Kit and your phone, press the “Answer/Disconnect” button on the Control Module. Press and hold for two seconds to activate the Voice Recognition function.
Chapter 2—錯誤! 尚未定義樣式。 Notes on using voice recognition Voice recognition is a feature of your phone which enables you to dial a number by simply saying a pre-recorded “voice tag”. Normally when you set a voice tag, you speak directly into the phone. When accessing this feature with the Car Kit, you may find it necessary to re-record the voice tag while you are in the car. This will set not only the way you say the voice tag, but also record a familiar background noise.
Bluetooth Car Kit user’s manual Siemens mobile phones setup This section describes setting up and using the Car Kit with a Siemens phone. Establishing a wireless connection Refer to the following to establish a wireless connection between your phone and the Car Kit. (Details on changing your phone’s settings are provided in the user’s manual that came with your phone.) 1. Turn on the car ignition, then turn on the phone. 2. Scroll through the Menu and select Connectivity. Press Select. 3.
Chapter 2—錯誤! 尚未定義樣式。 Disconnecting the phone The phone automatically disconnects when you are outside the 10-meter range of the junction box. To manually disconnect your phone, follow the procedure below. 1. Turn on the car ignition, then turn on the phone. 2. Scroll through the Menu and select Connectivity, then press Select. 3. Scroll to Bluetooth and press Options. 4. Scroll to Known devices and press Select. 5. Scroll to Triamp and press Options. 6. Scroll to Delete and press Select. 7. Press Yes.
Bluetooth Car Kit user’s manual Using the control module The Car Kit is operated using the following four-button control module: Answer/Disconnect Volume down Volume Up LED indicator light Redial/Voice Recognition Control Module Functions Answer/Disconnect Press to answer a call. Press again to hang up. Volume Down Press during operation to lower the volume. Volume Up Press during operation to increase the volume.
Chapter 2—錯誤! 尚未定義樣式。 Redial/Voice Recognition There is no redial function for Siemens phones. Pressing this button once will activate communication between the phone and the Car Kit, the LED will turn on, but there will be no phone call placed. To turn off the communication between the Car Kit and your phone, press the “Answer/Disconnect” button on the Control Module. Press and hold for two seconds to activate the Voice Recognition function.
Bluetooth Car Kit user’s manual Important! To ensure a successful reset, do not turn off your car ignition while resetting the Car Kit. Notes on using voice recognition Voice recognition is a feature of your phone which enables you to dial a number by simply saying a pre-recorded “voice tag”. Normally when you set a voice tag, you speak directly into the phone. When accessing this feature with the Car Kit, you may find it necessary to re-record the voice tag while you are in the car.
Chapter 2—錯誤! 尚未定義樣式。 19
Bluetooth Car Kit user’s manual Warranty information Please retain the sales receipt as proof of purchase. During the one-year warranty period, the product is eligible for replacement in case of defects in material and workmanship. In such cases, the defective unit will be repaired or replaced by the manufacturer or an authorized distributor. However, this warranty does not cover damages caused by improper use or from unauthorized modifications by third parties.
