Installation Guide
Technical Specifications
Part No. L-DCE30D-CON L-DCE60D-CON
Output:
DC Voltage 12V 12V
Rated Current 2.5A 5A
Rated Power 30W max. 60W max.
Minimum Load 3W 6W
Input:
Voltage Range 100-277VAC 100-277VAC
Frequency Range 47-63Hz 47-63Hz
Power Factor 0.99@120VAC 0.98@120VAC
(Typ.) @ full load 0.98@277VAC 0.95@277VAC
Efficiency 79% 83%
(Typ.) @ full load
Wiring Suitable for minimum 18AWG, rated min. 300V, min. 90°C
Protection:
Short Circuit Shut down o/p voltage, re-power on to recover after fault
condition is removed
Over Loading
≤
120% shut down o/p
≤
120% Hiccup mode, recovers
voltage, re-power on to automatically after fault
recover condition is removed
Over Temperature 100°C ± 10°C shut down o/p voltage, automatically
recover after cooling
Working Temperature -40°C ~ +60°C (see Derating Curve chart above)
IMPORTANT SAFETY INSTRUCTIONS
CAUTION: To reduce the risk of fire, electric shock, or injury to persons:
Read all instructions before installing system.
Before beginning installation, be sure power is turned OFF to the
power supply and light system.
• The 30W 12VDC Power Supply operates on line voltage 100-277 VAC.
The 60W 12VDC Power Supply operates on line voltage 100-277 VAC.
Shock Hazard: Whenever hardwiring the LED Power Supply to a 120-
volt circuit with an AC dimmer, turn off power at the circuit breaker before
installing. Failure to do so may result in serious personal injury or death.
Warning: All wiring must be in accordance with national and local
electrical codes, low-voltage Class 2 circuit. The Power Supply is to
be mounted and wired in accordance with Article 450 of the National
Electric Code (NEC). Failure to install the Power Supply and light fixture
in compliance with applicable codes and regulations may cause serious
personal injury, death and/or major property damage.
• Do not conceal the Power Supply inside a wall, ceiling, soft, or similar
permanent structure. The unit must be accessible.
< New Bullet 7/5
• Never install a Power Supply face down or resting on its side. For a
bank of multiple Power Supplies, mount the units with spacing at least
equal to the width of one unit. The Power Supply must be installed in
a well-ventilated area free from explosive gases and vapors. Do not
install in an airtight, boxed-in structure. The Power Supply is cooled
by circulating air and by mounting the unit flush to a surface to allow
for heat transfer. Operate the Power Supply at cooler surrounding
air temperatures to extend the life of the unit. See Derating Curve for
temperatures above 40°C (104°F).
• Operate only within the specified ambient temperature range of -40°C
(-40°F) to 60°C (140°F).
Note: It is normal for the LED Power Supply to feel warm when under
a full wattage load.
• The hardwired installation of the Power Supply should only be
performed by a qualified electrician.
• Do not conceal the line voltage input cord inside a wall, ceiling, soft, or
similar permanent structure, unless proper wire per NEC is being used. This
requirement does not apply to the 12VDC wiring between the Power Supply
and the cabinet light system. For low voltage wire runs inside a wall, ceiling,
soffit, or similar permanent structure, use CL2 or better cabling. †
• Do not install low-voltage Class 2 wiring along the same run as AC line
voltage
. If the line voltage and low-voltage wires need to cross, keep
them at 90° angles.
• Use only insulated staples or plastic ties to secure ALL loose wires.
• Route and secure wires so that they will not be pinched or damaged
when the cabinet is pushed to the wall.
(Continued on page 2)
LED DC Power Supply (30W)
L-DCE30D-CON
24 mm
15/16 in.
178 mm
7 in.
61 mm
2-3/8 in.
Cord
102 mm
4 in.
88 mm
3-7/16 in.
13 mm
1/2 in.
26 mm
1 in.
LED DC Power Supply (60W)
L-DCE60D-CON
54 mm
2-1/8 in.
155 mm
6-1/8 in.
20 mm
13/16 in.
LED Wall Dimmer
LED Power Supply
12VDC, 30W or 60W
Mounting Block
Install Wall Dimmer on
input (line voltage) side
of Power Supply
Line Voltage Input Cord
Neutral (white wire)
Ground (green wire)
Line (black wire)
INPUT
OUTPUT 12VDC
Red
Black
L Black
N White
12VDC+
LED DC Power Supply (30W)
L-DCE 30D-CON
24 mm
15/16 in.
178 mm
7 in.
61 mm
2-3/8 in.
Cord
102 mm
4 in.
88 mm
3-7/16 in.
13 mm
1/2 in.
26 mm
1 in.
LED DC Power Supply (60W)
L-DCE 60D-CON
54 mm
2-1/8 in.
155 mm
6-1/8 in.
20 mm
13/16 in.
LED Wall Dimmer
LED Power Supply
12VDC, 30W or 60W
Mounting Block
Install Wall Dimmer on
input (line voltage) side
of Power Supply
Line Voltage Input Cord
Neutral (white wire)
Ground (green wire)
Line (black wire)
INPUT
OUTPUT 12VDC
Red
Black
L Black
N White
12VDC+
Installation Instructions
Hardwire LED Power Supplies
Class 2 • Dimmable 30W & 60W 12VDC Constant Voltage
LED 12VDC Power Supply (30W) Part No: ........... L-DCE30D-CON
LED 12VDC Power Supply (60W) Part No: ........... L-DCE60D-CON
Mounting Block included with each Power Supply.
NOTE: These Hardwire LED Power Supplies are Dimmable.
For best operation, use LED-compatible wall dimmers.
100
80
60
40
20
-40 -20 0 10 20 30 40 50 60 70
Ambient Temperature (°C)
Load (%)
LED 12VDC Power Supply (30W)
L-DCE30D-CON
LED 12VDC Power Supply (60W)
L-DCE60D-CON
Typical Application
Derating Curve
Mounting Block
pre-wired to Power Supply
Page 1
Mounting Block option shown for illustrative purposes.