Assembly Instruction

Package Contents
Warnings and Cautions
1of2
Assembly Instruction Sheet
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal.
A
Crossbar Assembly
x1
(1)MediumBase60WVintagebulb(supplied),100WMaximum.
20-30minutes
Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtoensureallpartsare
present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.Contactcustomerserviceforreplacement
parts.
LightSource:
EstimatedAssemblyTime:
Preparation:
ToolsRequired: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses.
D
Vintage Bulb
x1
B
Alternate
Mounting screw
x2
(Step 2 Continued)
held tight with the mounting balls. If it is not, adjust the length of
the mounting screw or alternate short mounting screw on the
Crossbar Assembly (A) by unscrewing the preassembled hex nut
and lock washer and then screwing the mounting screws or
alternate short mounting screws in or out of the crossbar until the
correct length is achieved. Once the backplate and Fixture Body
(C) is secure, remove the mounting ball and Fixture Body (C) and
proceed to Step 3.
C
Fixture Body
x1
STEP 2 Test Fit the
Backplate to the Crossbar
Assembly
-
A. Remove the mounting balls
from the Crossbar Assembly
(A). Place the backplate and
Fixture Body (C) onto the
Crossbar Assembly (A) and
secure with mounting balls.
Note: The backplate and
Fixture Body (C) should be
snug against the wall and
C
Mounting
Ball
A
Backplate
Hex Nut and
Lock Washer
Figure 2
Mounting Screw
or Alternate Short
Mounting Screw
STEP 3 - Wire Connections
A. Use standard wire connectors (not included) to make all wire
connections. Twist connectors until wires are tightly joined together.
Wrap each connection with approved electrical tape and carefully
stuff all the connected wires into the Outlet Box.
Figure 3
White wire
from outlet box
White wire
from fixture
Black wire from
outlet box (or Red)
Black wire
from fixture
Bare, or Green
Ground wire
from outlet box
Ground wire
from fixture
Bare, or Green
Ground wire
from outlet box
OR
Ground wire
from fixture
Green Ground Screw
on the Crossbar
E
Socket Collar
x1
F
Steel Collar
x1
G
Glass Shade
x1
STEP 1 Installing the Crossbar Assembly-
A. Pass the supply wires through the Crossbar Assembly (A). Attach
the Crossbar Assembly (A) to the Outlet Box with the head of the
Green Ground Screw facing you. Secure the Crossbar Assembly (A)
with Outlet Box Screws (not included). Tighten until snug
Note: Use the Alternate Shorter Mounting Screw (B) if your
installation requires a shorter mounting screw.
.
Supply Wires
with Ground Wire
Outlet Box Screws
(not included)
Outlet
Box
A
Figure 1
Mounting Screw
or Alternate Short
Mounting Screw
STEP 4 Install the Fixture
Body
-
A. Position the backplate and
Fixture Body (C) onto the
Crossbar Assembly (A).
Place the holes in the
backplate over the mounting
screws or alternate short
mounting screws. Secure the
Fixture Body by using the
mounting balls and hand
tighten the mounting balls
until snug.
C
Mounting
Ball
A
Backplate
Figure 4
Mounting Screw
or Alternate Short
Mounting Screw

Summary of content (2 pages)