FCC Warning This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a commercial environment. This equipment generates, uses and radiates radio frequency energy. If not installed and used in accordance with the instructions, it may cause harmful interference to radio communications.
TABLE OF CONTENTS About This Guide .................................................................................. 1 Purpose ............................................................................................ 1 Overview of this User’s Guide .......................................................... 1 Introduction ......................................................................................... 3 Applications: ..............................................................................
Quick Setup .................................................................................... 17 Advanced Setup ............................................................................. 22 Technical Specifications .................................................................... 44 Limited Warranty ...............................................................................
ABOUT THIS GUIDE Congratulations on your purchase of this 4-Port Broadband Router! This device integrates 100Mbps Fast Ethernet and 10Mbps Ethernet network capabilities. This router is a complete solution for sharing the Internet and other office resources. Purpose This manual discusses how to install the 4-Port Broadband Router. Overview of this User’s Guide Introduction. Describes the Broadband Router and its features. Unpacking and Setup. Helps you get started with the basic installation of the Router.
INTRODUCTION With the explosive growth of the Internet, accessing information and services at any time, day or night, has become standard fare for most people. The era of the standalone PC is waning. Networking technology is moving out of the exclusive domain of corporations and into homes with at least two computers. Broadband network access is also gaining ground. Allowing more than two computers to access the Internet at the same time, however, has typically entailed significantly higher costs.
Applications: Broadband Internet access sharing: Enable several computers to share a single high-speed broadband Internet connection (LAN and WAN-Internet). Resource sharing: Share printers, scanners, and other peripherals. File sharing: Exchange data, messages, and files -- thus making good use of hard disk space. Online gaming: Your local area network allows you to play online games and use ecommerce services. Firewall: A built-in firewall function protects against hackers.
Features: 1 x 10/100Mbps port (WAN/Internet) 4 x 10/100Mbps Auto-MDIX ports (LAN) Supports Cable/DSL Modems with Dynamic IP, Fixed IP, PPPoE, and PPTP connection types Provides Network Address Translation (NAT) Firewall Supports Virtual Servers (Port Forwarding 10 Entries) and DMZ (5 Entries) Supports static routes (20 entries) Client Filtering by Date/Time (6 Entries and Special Applications Filter 10 Entries) MAC Address control to allow or deny access (32 entries) Supports Dyn
UNPACKING AND SETUP This chapter provides unpacking and setup information for the Broadband Router. Unpacking The box should contain the following items: TW100-S4W1CA Multi-Language Quick Installation Guide CD-ROM (User’s Guide) Network cable (1.5 m / 5 ft.) Power adapter (5V DC, 1A or 7.5V DC, 1A) If any item is found missing or damaged, please contact your local reseller for replacement.
HARDWARE INSTALLATION Front Panel The figure below shows the front panel of the 4-Port Broadband Router. 4-Port Broadband Router Front Panel POWER This indicator lights green when the hub is receiving power. Otherwise, it is off. WAN This indicator lights green when the WAN port is connected to an xDSL/Cable modem successfully. This indicator blinks green while the WAN port is transmitting data to or receiving data from the xDSL/Cable modem.
Rear Panel The figure below shows the rear panel of the 4-Port Broadband Router. 4-Port Broadband Router Rear Panel WAN On the 4-Port Broadband Router, there is an RJ-45 10/100Mbps AutoMDIX WAN port. This port connects to your xDSL/Cable modem. LAN (1-4) Four RJ-45 10/100Mbps Auto-MDIX ports for connecting to either 10Mbps or 100Mbps Ethernet connections.
Side Panel The figure below shows the side panel of the 4-Port Broadband Router. 4-Port Broadband Router Side Panel Power Port Plug the power adapter jack into this port RESET Use a pin-shaped object (such as a paperclip) to reset this device to factory default settings (Hold for 10 seconds and release). Resetting the device will also reset the login password to the default.
Hardware connections Connect the Internet Broadband Router 1. Connect one end of the network cable to the WAN port of the 4Port Broadband Router. 2. Connect the other end of the network cable to the Ethernet port of the xDSL or Cable modem. 3.
LAN ports. Since the Broadband Router has four ports, you can connect up to four computers directly to the unit. You do not have to buy a switch to connect these computers since the Internet Broadband Router functions as both an Internet connection-sharing unit and as a switch. Check the installation The LEDs of the Internet Broadband Router are clearly visible and the status of the network link can be seen immediately: 1.
PC NETWORK TCP/IP SETTING The network TCP/IP settings differ based on the computer’s operating system (Windows 7/Vista/XP/2000/NT/ME/98SE) and are as follows. Windows 7/ Vista 1. Go to Control Panel and select Network and Share Center 2. Click on View Status and click Properties. 3. Click on Internet Protocol Version 4 (TCP/IPv4) and select Properties. 4. Select Obtain an IP Address Automatically. 5. Select Obtain DNS Server Address Automatically.
Windows XP/2000 1. Right click My Network Places and select Properties 2. Double-click on the Local Area Connection icon and click Properties. 3. Click on Internet Protocol (TCP/IP) and select Properties. 4. Select Obtain an IP Address Automatically. 5. Select Obtain DNS Server Address Automatically. 6. Click OK. Windows NT4.0 Click on the “Start” button located on the lower left corner of the menu bar.
Select “Settings” and then “Control panel.” In the “Control panel” window, select “Network” to enter the TCP/IP settings window. 1. Set “IP address” to “Obtain an IP address automatically.” 2. Set “DNS” to “Disable DNS.
Windows 95/98/ME 1. Right click on the “Network neighborhood” icon and select properties. 2. Select the TCP/IP for your Ethernet adapter and then click properties. 3. Select “Obtain an IP address automatically” in the “IP Address” tab. 4. Click on the DNS configuration tab and select “Disable DNS”.
5. Click on the Gateway tab. If there are any Installed gateways, select the gateway and click Remove. 6. Click OK.
4-PORT BROADBAND ROUTER CONFIGURATION First, make sure that the network connections are functioning normally. This Internet Broadband Router can be configured using Internet Explorer 6.0 or later. Login into the 4-Port Broadband Router 1. Open Internet Explorer 6.0 or higher. 2. Enter http://192.168.10.1 (the factory-default IP address setting) in the address bar. 3. When the following dialog box appears, type in admin for the user name. Type in admin for the password and click OK.
4. Two setup options appear: Quick Setup or Advanced Setup. It is recommended that you use Quick Setup if you are a beginner. It will lead you through the configuration step-by-step. Quick Setup On the main webpage, select “Quick Setup” to specify the Time Zone and the WAN connection type. 1-1 Time Zone Select the appropriate time zone so your system clock can synchronize itself through the SNTP Server.
1-2 WAN Connection Type To select the WAN connection-type, click Dynamic IP (Cable Modem), Static IP (Fixed-IP), PPPoE (Dial-up xDSL) or PPTP 1-2-1 Dynamic IP (Cable Modem) To connect to a Dynamic IP (Cable Modem) Internet connection with the Broadband Router, check the cable modem with the related user’s guide. The Cable modem will automatically configure itself, and the Broadband Router is configured to automatically assign addresses to each PC. If required by your ISP, input a host name and MAC address.
1-2-2 Static IP If your Internet Service Provider (ISP) has assigned you a fixed IP address, select this option. Enter the assigned IP address, subnet mask, and gateway IP for your Broadband Router. 1-2-3 PPPoE (Dial-up xDSL) If your DSL Internet connection is PPPoE (Dial-up xDSL), your ISP will provide a Password and Username. Select this option, and enter the required information. If your ISP provides a Service Name, enter it in the Service Name field. Otherwise, leave it blank.
The Service Name, IP Address, and DNS Address fields must be completed if your ISP provided you with this information. If your ISP Provider provides a Dynamic IP Address, you should skip these fields. The MTU feature specifies the largest packet size permitted for network transmission. Enter the value desired; for most DSL users, 1492 is recommended. By default, MTU is set at 1492.
appropriate fields. If your ISP has provided you with a Connection ID, enter it in the Connection ID field. Otherwise, leave it blank. The MTU feature specifies the largest packet size permitted for network transmission. Enter the value desired; for most DSL users, 1492 is recommended. By default, MTU is set at 1492. The Maximum Idle Time feature can control the connection time (default time=0, always connect).
1-3 DNS The Domain Name System (DNS) is the way that Internet domain names are translated into Internet Protocol (IP) addresses. If your ISP provided at least one DNS Server IP Address, type that IP Address in the Primary DNS address fields. You may also enter another DNS Server IP Address; the Router will utilize these simultaneously for quicker access to functioning DNS Servers.
2-1-1 System Time Connecting to a Simple Network Time Protocol (SNTP) server allows the Broadband Router to synchronize the system clock to the global Internet time through the SNTP Server. The synchronized clock in the Broadband Router is used to record the system log and control client filtering. 2-1-2 Administrator Settings Password Settings Set a password if you wish to restrict management access to the Broadband Router.
Remote Management To manage the Broadband Router from a remote location (outside of the local network), you must specify the IP address of the remote PC. Leave the IP address as 0.0.0.0, to allow open access to the router. UPnP (Universal Plug and Play) To enable UPnP functionality, check the Enable box. The Advertise Time is the interval the router will send out UPnP advertisements. By default, the router will send out an advertisement every 1800 seconds.
While updating the firmware, please wait after pressing the Apply button, and follow the instructions on the screen; the Power Light on the front panel will start blinking when the firmware has been upgraded successfully.
2-1-4 Configuration Tools Use the "Backup Settings" tool to save the Broadband Router's current configuration to a file named "config.bin" on your PC. You can then use the "Restore Settings" tool to restore the saved configuration of the Broadband Router that was set previously. Select "Restore to Factory Defaults" tool to force the Broadband Router to reset and restore the original factory settings.
2-1-5 Status The status screen will display the Broadband Routers' WAN/LAN interfaces, firmware and hardware version numbers, and the number of connected clients to the network.
2-1-6 System Log View any attempts that have been made to gain access to the network.
2-2 WAN The Broadband Router supports the following types of Internet connections: Dynamic IP Address, Static IP Address, PPPoE, and PPTP. 2-2-1 Dynamic IP The Host Name is optional, but may be required by some Service Providers. The default MAC address is set to the WAN's physical interface on the Broadband Router. If the Service Provider requires the MAC address, type it in. Click the "Clone MAC Address" button to copy the MAC address of the Network Interface Card installed in the PC.
2-2-2 Static IP If the Service Provider has assigned a fixed IP address, enter the assigned IP address subnet mask and gateway address provided. Click “yes” if are using two or more IP addresses. 2-2-3 PPPoE (Dial-up xDSL) If you’re connecting to the Internet using a PPPoE (Dial-up xDSL) Modem and your ISP has provided you with a Password and Username, then your ISP uses PPPoE. Select this option, and enter the required information. If the ISP provided a Service Name, enter it in the Service Name field.
The Service Name, IP Address, and DNS Address fields must be completed if your ISP provides you with this information. If your ISP provides a Dynamic IP Address, skip these fields. The MTU feature specifies the largest packet size permitted for network transmission. Enter the value desired; for most DSL users, 1492 is recommended. By default, MTU is set at 1492. The Maximum Idle Time feature can control the connection time (default time=0, always connect).
2-2-4 PPTP If connecting to the Internet using a PPTP Modem, enter the PPTP Account Name, PPTP Password, Host Name, Service IP Address, your IP Address, and your Subnet Mask as provided by your ISP in the appropriate fields. If your ISP has provided you with a Connection ID, enter it in the Connection ID field. Otherwise, leave it blank. The MTU feature specifies the largest packet size permitted for network transmission. Enter the value desired; for most DSL users, 1492 is recommended.
The Maximum Idle Time feature can control the connection time (default time=0, always connect). Check the Connect-on-demand box to enable your router to connect your ISP whenever an Internet connection is required. 2-2-5 DNS The Domain Name System (DNS) is the way that Internet domain names are translated into Internet Protocol (IP) addresses. If your ISP provided at least one DNS Server IP Address, type that IP Address in the Primary DNS address fields.
2-2-6 Dynamic DNS The Dynamic DNS feature allows you to host a server (Web, FTP, Game Server, etc.) using a host name with your dynamically assigned IP address. Most broadband Internet Service Providers assign dynamic IP addresses. When you use a Dynamic DNS service provider, your friends can enter your host name to connect to your server, no matter what your IP address is. Use Dynamic DNS Check this option to enable Dynamic DNS.
Enter the username provided by your Dynamic DNS service provider. Password Enter the password provided by your Dynamic DNS service provider. 2-3 LAN To set the LAN’s IP Address and configure DHCP server settings. 2-3-1 LAN Settings The default value is 192.168.10.1 for the IP address and 255.255.255.0 for the Subnet Mask. You may change the value according to your needs. To enable the DHCP server to allocate dynamic IP addresses to the clients PCs, click “Enable”.
The Lease Time is the amount of time a network user will be allowed to connect to the Router with his/her current dynamic IP address. Enter the amount of time, in hours, days or weeks, which the user will be “leased” this dynamic IP address. You can enter your local domain name in the Local Domain Name fields. 2-3-2 DHCP Client List The DHCP client list allows you to see which clients are connected to the router via IP address, host name, and MAC address.
TCP (Transmission Control Protocol) - A method (protocol) used along with the Internet Protocol (Internet Protocol) to send data in the form of message units between computers over the Internet. While IP takes care of handling the actual delivery of the data, TCP takes care of keeping track of the individual units of data (called packets) that a message is divided into for efficient routing through the Internet.
Example: ID Trigger Port Trigger Type Public Port Public Type Comment 1 28800 UDP 2300-2400, 47624 UDP MSN Game Zone 2 28800 UDP 2300-2400, 47624 TCP MSN Game Zone
2-4-2 Virtual Server The virtual server option allows you to define port number on your router for redirection to an internal LAN IP address. This feature is useful for hosting online services such as FTP or Web servers. Up to 10 entries. Example: ID Server IP Mapping Port Type Comment 1 192.168.10.20 80 TCP Web Server 2 192.168.10.12 20 TCP FTP Server 3 192.168.10.12 21 TCP FTP Server 4 192.168.10.
2-5 Firewall The 4-Port Broadband Router provides extensive firewall protection by restricting connection parameters to limit the risk of hacker attacks and by defending against a wide array of common hacker attacks. The 4-Port Broadband Router provides packet filtering rules by restricting service ports, IP address or MAC address. However, for applications that require unrestricted access to the Internet, you may configure a specific client/server as a demilitarized zone (DMZ).
Example: 2-5-3 MAC Address Control MAC Address Control allows you to block certain client PCs from accessing the Internet based on MAC addresses. Up to 32 entries.
2-5-4 DMZ (Demilitarized Zone) If a local client PC cannot run an Internet application properly from behind the NAT firewall, open the client up to unrestricted two-way Internet access by defining a PC as a virtual DMZ Host. Up to 5 clients can be mapped to specific public IP addresses. Multiple DMZ entries only apply if you are using a static IP address from your ISP and you have multiple static public IP addresses assigned by your ISP.
2-5-5 URL Filter The URL filtering feature will allow you to deny access to specific websites. 2-6 Routing Allows you to create or define static routes on the LAN. Up to 20 static routing entries. 2-6-1 Static Routing Static routing allows you to define routes to other networks to routing devices or routers that are located on your LAN network.
TECHNICAL SPECIFICATIONS Hardware Standards IEEE 802.3 10BASE-T Ethernet; IEEE 802.3u 100BASE-TX Fast Ethernet Network Protocols TCP/IP, NAT, PPPoE, UPnP, HTTP, DHCP Server, SNTP WAN 1 x 10/100Mbps Auto-MDIX port (Internet) LAN 4 x 10/100Mbps Auto-MDIX ports Cabling Ethernet: Cat. 5 up to100 m Fast Ethernet: Cat.
Certifications CE, FCC Router Connection Type Dynamic IP, Static (Fixed) IP, PPPoE, PPTP Firewall NAT UPnP IP / MAC Address Filter (32 entries) Domain / URL Blocking (32 entries) Scheduling (6 entries) Special Applications (10 entries) Virtual Servers (6 entries) DMZ (5 entries) Routing Static Routes (20 entries) VPN IPSec, L2TP, PPTP pass-through (Up to 8 VPN sessions) Management Web browser configuration
LIMITED WARRANTY TRENDnet warrants its products against defects in material and workmanship, under normal use and service, for the following lengths of time from the date of purchase. TW100-S4W1CA – 3 Years Warranty AC/DC Power Adapter, Cooling Fan, and Power Supply carry 1 year warranty.
abuse, or improper use (iii) the product was subject to conditions more severe than those specified in the manual. Warranty service may be obtained by contacting TRENDnet within the applicable warranty period and providing a copy of the dated proof of the purchase. Upon proper submission of required documentation a Return Material Authorization (RMA) number will be issued. An RMA number is required in order to initiate warranty service support for all TRENDnet products.
PRODUCT DOES NOT EXIST OR WAS CAUSED BY CUSTOMER’S OR ANY THIRD PERSON’S MISUSE, NEGLECT, IMPROPER INSTALLATION OR TESTING, UNAUTHORIZED ATTEMPTS TO REPAIR OR MODIFY, OR ANY OTHER CAUSE BEYOND THE RANGE OF THE INTENDED USE, OR BY ACCIDENT, FIRE, LIGHTNING, OR OTHER HAZARD.
Go to http://www.trendnet.com/gpl or http://www.trendnet.com Download section and look for the desired TRENDnet product to access to the GPL Code or LGPL Code. These codes are distributed WITHOUT WARRANTY and are subject to the copyrights of the developers. TRENDnet does not provide technical support for these codes. Please go to http://www.gnu.org/licenses/gpl.txt or http://www.gnu.org/licenses/lgpl.txt for specific terms of each license.
