English QIG Le Thank you for purchasing the TW100-S4W1CA. This router wife allow you fo share your internet connection with multiple users while ifs firewall protects your network from hackers. Thai guide will help you set up and configure your router. Following the installation instructions should be quick and easy. If you run info problems, please refer to the Troubleshooting section or fhe more delayed installation procedures on the User's Guide. If you need further technical support, please visit www .
Collect Internet Service Provider (ISP) Information During the installation of your router the Se-Up Wizard will ask you for pacific Internet Vicar Provider ISP information you should have bean provided from your ISP fo set up your Cable or DSL connection. The information is different based on your type of Interment Connection. Please verify your Internet Connection type and ensure you have the following information: Dynamite IP Cable Connection Nothing required.
pal LATTE 4. Tum off your Cablecast Modem, Router, and PC. 2. Connect one RI-45 network cable from the Modern's Theme port to the Routers WAN port, 3. Connect a different JR-45 network cable from one of the Router's LAN ports fo your computer's network port. 4. Tum on your Cablecast modem. 5. Turn on your router. §. Tum on your computer. TWIB-BAICA. POWER Verify Hardware Installation Verify that the following router front pans lights are on: Power, WAN, and ona LAN port.
3. Configure the computer's TCP/IP Settings This next section will ensure that your computer can communicate with your router. To do this, you will need to configure the TC PAP settings in your Operating Oyster (08). Configuration instructions for Windows 0-based computers are shown below. For computers running other operating systems, 38% your system documentation for configuration instructions, Wind 95/98/98SE/ME 1, Find Start Bunion located on Desktop. 2.
§, Under the IP Address Tab, select Obtain an IP address automatically. &. Now go to the Gale's tab and make sure no Gateways are listed in the Installed Gateway's section.
¥. Go to the DNS Configuration fab and click Disable DNS. Then click OK. 8. Click OK on the TC PAP Properties box. 8. Click OK on the Network Box, 48. At this point, the installation may require files from your Windows CD-ROM. if this happens, insert Windows 98 CD-ROM info your CD-ROM drive and select CD-ROM drive to lead the files. 14. After the Ales oad, the System Settings Change message appears, click Yes to reboot your system. Your computer will now load your new TCP/IP sailings.
12. After your system reboots, click Start; click on Run. Then type windpipe in the field and click OIC. 43. The IP configuration box will appear. Chooses your Network adapter from the drop down bex (such as Trend net TE100-PCIWHN 10/100Mbps network adapter land the cement IP address information of your computer will show in the bax, including the following: IP Address, Subset Mask and Default Gateway. 44.
Windows 2000/XP 1. Click Start; click Settings, and dick on Control Panel. 2, Double-click the Network Connections icon. 3. Right-click on tha Local Area Connection loon, and then click on Properties. The Local Area Connection Properties box will appear. 4. Under the "General Configuration” Tab, locate and select TC PAP and then click Properties. The Inflate Protocol (TCP/IP) Properties box will appear.
§. Click OK. 7. Click Gloss on the Local Area Connection Properties box. 8, Click on Start; click on Run. Then type omd and kickoff The Command Prompt window will appear. Type configure at the C:\ prompt and prose the Enter key. 10. ¥ your IP Address shows the following information your computer is now successfully convalesced to the router: IP Address: 192.188.1.x Subset Mask: 255.265.255.0 Default Gallows: 182.188.1.
ET The following set-up information is designed to help you to set-up your router fo correct to the Internet. The set-up is different depending upon the type of Internet Connection you have with your ISP. If you'rs nof sure what type of connection you have plasma contact your Internet Service Provider and collect the required information, which is located in the “Prepare for installation” section at the beginning of this Quick Installation Guide. 4.
3. Click Quick Setup to configure your Router for Broadband Infest access. 4, Click on the drop down mer to select the appropriate time zones. If your region runs on Daylight Savings Time, you should enable the “Sat Daylight Saving” option and input the dales and times when Daylight Savings Time gods into and out-of artifact. Than, click Next.
§. Select the appropriate WAN connection type by clicking on Dynamic IP, Static IF, POE, or PT. Dynamic IP 1. Pacify ihe Host Nam, {if any} and Clone the MAC Address {if required by your ISP). Click Next. Barns wr pr 2. Specify Primary and Secondary DNS addresses if you wish fo use DNS addresses other than your ISP-provided DNS addresses. Click Finish.
3. You may verify your Interment connection on the Status page by typing Ftp: wrens Trendsetter In your browser's address bar and hitting Enter. If the website appears, your router is configured properly. Static or Fixed IP Cable Connection 1. Enter the IP Address, Subtenant Mask, and ISP Gateway Address provided by your ISP. Click Next. gp ERT Specify Primary and Secondary DNS addresses ff you wish to use DNS addresses other than your ISP-provided DNS addresses. Click Finish.
3. You may verify your Interment connection on the Status page by typing tip lean Trendsetter in your browser's address ber and hitting Enter. If the websites appears, your router is configured properly. NOTE: 1 the rebuild dose nol appear, please very your conditioned | ype with yur 188 Poe 1. Enter your Poe User Name and Password, and retypes your password, Then, click Next.
2. Specify Primary and Secondary DNS addresses if you wish to use DNS addresses other than your ISP-provided DNS addresses. Click Finish. 3. You may verify your Interment connection on the Status page by typing HTTP: wrangler TREND NET. com in your browser's address bar and hitting Enter. if the website appears, your router is configured properly. / NOTE: 1 ihe label code nol appear, plans very your connection | Lyme with your 189.
PT A. Enter your PT User Name and Password, dins retype your password. Then, dick Ext. 2. Specify Primary snd Secondary DNS addresses if you wish to use DNS other than your ISP-provided DNS addresses. Click Finish.
3. You may verify your infest connection on the Status page by typing Pity: hearer Endometrium in your browser's address bar and hiring Enter. if the website appears, your router is configured properly. MOTE: If the website toes not spewer, please variably your conciliation type with your ISP For detailed information about the TW100-84WICA's configuration and advanced settings, pleas refer to the Troubleshooting scion, User's Guido CD-ROM or Trendiness's website www.trendnet.com.
ELF CF. When | attempt to access hitp192.968.1.1 In my web browser, an aor sewerage fells me “The page cannot be displayed.” Huw can | gel into the TW0SS4WICA web configuration page? A, Verify your hardware and TOPAZ seeings again by reviewing the instructions in sections 1-3. Also, make sure the Power, WAN, and on the LAN light on the Router's frond panel are on. Then, ry crossing again using your web browser. £32. 1 don't know what my Internet Connection Type | have.
