i
Table of Contents 1. Introduction ......................................................................................................... 1 Features ............................................................................................................................. 1 Package Contents .............................................................................................................. 1 System Requirements....................................................................................
1. Introduction The TU2-ETG is a Gigabit USB network adapter that allows you to instantly connect to a 10/100/1000Mbps network from a USB enabled desktop or laptop. Compliant with USB 2.0 and backwards compatible with the USB 1.0 and 1.1, you can share files and printers and also gain access to broadband Internet to explore valuable resources on the web. Features Compliant with USB 2.0 and 1.1 specifications Compliant with IEEE 802.3, 802.3u and 802.
LED Status LED Color Status Description Link Green Off Link is not established. On Link is established. Off Link is not established 1000Mbps Green Link to 10/100Mbps network. On Link to 1000Mbps network. Blinking There is 1000Mbps traffic flow over the network.
2. Installation Driver Installation Note: DO NOT connect the Ethernet adapter to your computer before completing the driver installation. 1. Insert the provided CD into your CD-ROM drive. 2. Click Run Autorun.exe (Windows 7/Vista only). 3. Click Install Driver. Then click your operating system. 4. Connect the Ethernet adapter’s USB end to a free USB port of your computer. 5. Drivers will install automatically.
Verifying the Driver Installation in Windows To verify your Ethernet adapter installation, please launch Device Manager by the steps below: On Windows 7/Vista: Right-click on the Computer icon on the desktop and select Properties > Device Manager. On Windows XP/2000: Right-click on the My Computer icon on the desktop and select Properties > System > (Hardware) > Device Manager. In the Network adapters group, a string similar to USB2.0 to Gigabit Ethernet Adapter should be displayed.
Upon your connection, a message pops up in the notification area indicating your connection speed. The adapter’s AutoSense feature can automatically detect the network's maximum line speed. To have a 1000Mbps connection, your network device (e.g., switch, router or DSL modem) must also support 1000Mbps. Configuring Network Settings You should configure your Ethernet adapter as required according to your network environment.
In the Network Connections folder, double-click the connection icon for your adapter. Then the Local Area Connection Properties window appears.
Mac Driver Installation Mac OS X 10.5.2 ~ 10.6 1. Mac has built in driver. Please connect the Ethernet adapter to a free USB port. The system will pop up a message “A new network interface has been detected” 2. If the message is not pop up , please start System Preferences and select Network, then click the ”＋” to add an “USB Gigabit Ethernet “ service. Click “Network Preferences…” to setup, 3. Select “USB Gigabit Ethernet “ then click “Advanced” to setup the network by either using static IP or DHCP.
3. If select “Using DHCP” Mode, please click”Renew DHCP License“ to get the IP address , Otherwise, please enter the IP information that provided by your Network Service Provider. 4. A new Ethernet network connection is established.
5. To verify the installation, please click open GO > Utilities > System Profile > Hardware > USB > to see if the Ethernet adapter is properly installed.
3. Specifications Hardware Standards USB 2.0, 1.1 IEEE 802.3: 10Base-T IEEE 802.3u: 100Base-TX IEEE 802.3ab: 1000Base-T Data Transfer Rate Ethernet: 10Mbps/20Mbps (Half/Full Duplex) Fast Ethernet: 100Mbps/200Mbps (Half/Full Duplex) Gigabit: 2000Mbps (Full Duplex) Embedded Buffers 20KB SRAM 20KB SRAM Supported OS Windows 7(32/64-bit) / Vista 32/64-bit) / XP (32/64-bit), 2000 Mac 10.5.2~10.
Limited Warranty TRENDnet warrants its products against defects in material and workmanship, under normal use and service, for the following lengths of time from the date of purchase. TU2‐ETG – 3 Years Limited Warranty AC/DC Power Adapter, Cooling Fan, and Power Supply carry 1 year warranty.
limited to, duty, tax, and other fees. WARRANTIES EXCLUSIVE: IF THE TRENDNET PRODUCT DOES NOT OPERATE AS WARRANTED ABOVE, THE CUSTOMER’S SOLE REMEDY SHALL BE, AT TRENDNET’S OPTION, REPAIR OR REPLACE. THE FOREGOING WARRANTIES AND REMEDIES ARE EXCLUSIVE AND ARE IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED, EITHER IN FACT OR BY OPERATION OF LAW, STATUTORY OR OTHERWISE, INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
13
