Regulatory notes and statements Wireless LAN, Health and Authorization for use Radio frequency electromagnetic energy is emitted from Wireless LAN devices. The energy levels of these emissions however are far much less than the electromagnetic energy emissions from wireless devices like for example mobile phones. Wireless LAN devices are safe for use frequency safety standards and recommendations.
- Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This device complies with Part 15 of the FCC Rules.
Europe – EU Declaration of Conformity This device complies with the essential requirements of the R&TTE Directive 1999/5/EC.
[Czech] Česky TRENDnet tímto prohlašuje, že tento TEW-623PI je ve shodě se základními požadavky a dalšími příslušnými ustanoveními směrnice 1999/5/ES. [Danish] Dansk Undertegnede TRENDnet erklærer herved, at følgende udstyr TEW-623PI overholder de væsentlige krav og øvrige relevante krav i direktiv 1999/5/EF.
This product or software contains encryption code that may not be exported or transferred from the US of Canada without an approved US Department of Commerce export license. Safety Information Your device contains a low power transmitter. When device is transmitted it sends out radio frequency (RF) signal. CAUTION: To maintain compliance with FCC’s RF exposure guidelines, this equipment should be installed and operated with minimum distance 20cm between the radiator and your body.
TABLE OF CONTENT Introduction ................................................................................................ 1 Overview of this User’s Guide ............................................................................... 1 Unpacking and Setup .................................................................................. 2 Unpacking .............................................................................................................. 2 Setup ....................................
INTRODUCTION Congratulations on your purchase of this 300Mbps 802.11n Wireless LAN Adapter. This manual contains detailed instructions regarding the operation of this product. Please keep this manual for future reference. With the 300Mbps 802.11n Wireless LAN Adapter, a desktop or laptop computer can communicate with another computer wirelessly. An easy-to-use utility is bundled with the 300Mbps 802.11n Wireless LAN Adapter for configuration, monitoring, and diagnostic purposes. The 300Mbps 802.
UNPACKING AND SETUP This section provides unpacking and setup information for the 300Mbps 802.11n Wireless LAN Adapter. Unpacking The box should contain the following items: TEW-623PI PCI Adapter CD-ROM (Utility/Driver and User’s Guide) Multi-Language Quick Installation Guide If any item is found missing or damaged, please contact your local reseller for replacement.
HARDWARE INSTALLATION LED Indicator for CardBus Link The Link LED indicator lighted green when the 300Mbps Wireless N PCI Adapter is connected to wireless network successfully. ACT (Activity) The ACT LED indicator blinking green when the 300Mbps Wireless N PCI Adapter is transmitting or receiving data. LED Indicator for PCI Link The Link LED indicator lighted green when the 300Mbps 802.11g Wireless LAN Adapter is connected to wireless network successfully.
SOFTWARE INSTALLATION This section describes how to install the driver and utility for the 300Mbps Wireless N PCI Adapter. Note: DO NOT install the 300Mbps 802.11g Wireless LAN Adapter in the computer until instructed to do so. Windows Utility and Driver Installation 1) Insert the CD-ROM into your CD-ROM drive, the Autorun will appear. 2) Click “Install Utility & Driver” icon to install the driver and software and the install wizard will begin installing the software.
When the Wireless LAN Adapter was installed, you will see the icon on the Windows task bar. The user can configure the wireless settings using the Wireless Adapter Configuration Utility.
Link Information This is the default screen after launching the Utility program. Status: Shows the associated BSSID, which can be used to identify the wireless access point. SSID: Shows the current SSID, which must be the same on the wireless client and AP in order for communication to be established. Wireless Mode: Shows the current wireless mode used for wireless communication. Encryption: Shows the current encryption mode used on the wireless network.
Configuration This screen is where you set the basic wireless settings for the Wireless LAN Adapter SSID: Service Set Identifier, which is a unique name shared among all clients in a wireless network. The SSID must be identical for each client in the wireless network. Wireless Mode: There are two modes available for selection ● Infrastructure – to establish wireless communication with the LAN and other wireless clients through the use of Access Points.
Open or Shared Key Open System and Shared Key require the user to set a WEP key to exchange data with other wireless clients that have the same WEP key. z Default Key: select one of the 4 keys to use. z Network Key: choose the encryption way, either in HEX or ASCII formats, and enter the password in the blank space. z Key Length: select 64 or 128 bits as the length of the keys Key Format: HEX or ASCII WPA-PSK/WPA2-PSK If WPA-PSK/WPA2-PSK is selected the below window appears. Please enter a WPA Passphrase.
WPA-PSK/WPA2-PSK If WPA/WPA2 is selected, configuration is enabled. Please click the “configuration” button. Select a certification for drop down list.
Site Survey This screen allows the user to scan for available wireless networks (wireless clients and Access Points). It also allows the user to establish wireless communications with an available wireless network. Available Network – displays the wireless networks (wireless clients and access points) that are within range. Select any one of the wireless networks by double-clicking on it or clicking on the “Connect” button. Click the “Refresh” button to scan for available networks.
Profile Profile – The user can create and manage the created profiles for home, work or public areas. By double-clicking on one of the created profile, the setting will adjust to the specific setting such as SSID, channel, and encryption as saved by that particular profile. Remove: Deletes the selected profile Add: Adds a profile. The following screen will appear.
WPS Wi-Fi Protected Setup (WPS) is an optional certification program from the Wi-Fi Alliance that is designed to ease the task of setting up and configuring security on a wireless network. There are two methods used in the WPS as below instruction. Push the button on my access point Using the WPS configuration with the “Push the button on my access point” method, the configuration steps as below: 1) Selected the “Push the button on my access point”.
4) If the WPS configuration was successful, the follow window will appear. 5) If the WPS configuration failed, the follow window will appear.
Enter a PIN into my access point Using the WPS configuration with the “Enter a PIN into my access point” method, the configuration steps as below: 1) Selected the “Enter a PIN into my access point”, the PIN will be show on the button of the windows. 2) Enter the PIN code into the WPS “Clint PIN number” of you wireless access point or router then click the Start PIN button, the wireless access point or router will start the WPS configuration process.
4) If the WPS configuration was successful, the follow window will appear. 5) If the WPS configuration failed, the follow window will appear.
About This screen displays information about the Wireless LAN Adapter, such as the Driver and Utility version. When a new version of the utility becomes available for upgrade, users will be able to identify by version numbers.
Technical Specifications General Radio Technology IEEE 802.11b Direct Sequence Spread Spectrum (DSSS) IEEE 802.11g Orthogonal Frequency Division Multiplexing (OFDM) IEEE 802.11n Orthogonal Frequency Division Multiplexing (OFDM) Interface PC Card: 32‐bit CardBus, PCI Adapter: 32‐bit PCI bus Data Transfer Rate 802.11b: up to 11Mbps 802.11g: up to 54Mbps 802.
Physical and Environmental Driver Support Windows 7 (32/64‐bit), Vista (32/64‐bit), XP (32/64‐bit), 2000 Temperature Operating: 0° ~ 40° C, Storage: ‐10° ~ 70° C Humidity 10% ~ 95% RH, no condensation Dimensions PC Card:, 115 x 54 x 8.7 mm, PCI Adapter: 13 x 121 x 21.
Limited Warranty TRENDnet warrants its products against defects in material and workmanship, under normal use and service, for the following lengths of time from the date of purchase. TEW‐623PI – 3 Years Warranty AC/DC Power Adapter, Cooling Fan, and Power Supply carry 1 year warranty.
PERSON TO ASSUME FOR IT ANY OTHER LIABILITY IN CONNECTION WITH THE SALE, INSTALLATION MAINTENANCE OR USE OF TRENDNET’S PRODUCTS.
