300Mbps Wireless N VPN Router TEW-659BRV ŸQuick Installation Guide (1) ŸTroubleshooting (7) 1.
1. Before You Start Package Contents ŸTEW-659BRV ŸCD-ROM (User's Guide) ŸMulti-Language Quick Installation Guide ŸNetwork Cable (1.5m / 5ft) ŸPower Adapter (12V DC, 1A) If any of the above contents are missing, please contact your reseller. Minimum Requirements ŸA computer with a wired or wireless network adapter properly installed (Note: It is recommended that you configure the Wireless Router from a wired computer) ŸWeb Browser: Internet Explorer (6.0 or higher), Firefox (2.
2. Power off your Cable or DSL modem. 6. Connect the Power Adapter to the TEW-659BRV and then to a power outlet. Push the power button to the “On” position. 3. Disconnect the network cable from your Cable or DSL modem and your computer. 4. Connect one end of a network cable to one of the TEW-659BRV's network ports. Connect the other end of the cable to the computer's network port. 7. Power on your cable or DSL modem. Wait until the LEDs indicate that thye modem is fully booted up.
3. Configure the Wireless Router Note: 1. It is recommended that you configure the Wireless Router from a wired computer. 2. For VPN configuration instructions please refer to the User's Guide. The User's Guide is located on the provided CD-ROM. 1. Open your web browser, type http://192.168.10.1 in the Address Bar, and then press Enter. 5. Enter the Old password (By default, the Password is admin), enter a New Password, reconfirm the New Password and then click Next. 2.
6. Select your Time Zone and then click Next. 9. You will need to configure the following: Wireless (Enable/ Disable): The default setting (Enable) must be selected. Select Disable if you do not want any wireless computers or devices to connect to this device. Network ID (SSID): The SSID is the wireless network name of your wireless network (e.g. wireless router or access point). Enter a unique SSID. Choose something that you would easily identify when searching for available wireless networks. 7.
Note: 1. To protect your network from any unauthorized access it is recommended to enable wireless encryption. 2. The example below is for WPA-PSK/WPA2-PSK (AES) security. If you select WPA-PSK or WPA2-PSK, make sure your wireless adapters support WPA or WPA2. If your wireless adapters do not support WPA or WPA2, then select WEP. 3. WEP encryption only supports 802.11b/g speed of up to 54Mbps. 4.
14. Open up your browser and enter in a URL (e.g. http://www.trendnet.com) to verify that you have Internet connection. Your configuration is now complete For detailed information regarding the TEW-659BRV’s configuration and advanced settings, please refer to the User's Guide included on the CD-ROM, or TRENDnet's website at http://www.trendnet.com.
Troubleshooting 1. I typed http://192.168.10.1 in my Internet Browser's Address Bar, but an error message says “The page cannot be displayed.” How can I get into the TEW-659BRV's web configuration page? 1. Check your hardware settings again by following the instructions in Section 2. 2. Make sure the Network Port and Wireless lights are lit. 3. Make sure your TCP/IP settings are set to Obtain an IP address automatically (see the steps below). 4. Reset the TEW-659BRV.
Windows XP/2000 1. Go into the Control Panel, doubleclick the Network Connections icon and then right-click the Local Area Connection icon and then click Properties. 2. Click Internet Protocol (TCP/IP) and then click Properties. Then click on Obtain an IP address automatically. 2. I am not sure what type of Internet Account Type I have for my cable/DSL connection. How do I find out? Contact your Internet Service Provider's (ISP) support service for the correct information. 3.
5. Please give me an explanation of all the LEDs and Buttons.
TRENDnet 20675 Manhattan Place Torrance, CA 90501. USA Copyright ©2011. All Rights Reserved. TRENDnet.
