Quick Installation Guide TI-PG541i
Table of Content 1 English 1. Before You Start 2. Quick Reference 3. Hardware Installation 4. Hardware Configuration 5.
1. Before You Start Package Contents Ÿ TI-PG541i Ÿ Quick Installation Guide Ÿ CD-ROM (User's Guide) Minimum Requirements Ÿ Power supply (ex. model TI-S24048 or 48VDC3000) Ÿ Networked computer Ÿ RJ-45 Network Cable Optional Equipment Ÿ 35 mm DIN-Rail Ÿ SFP modules (e.g. TEG-MGBSR, TEG-MGBS80, TEG-MGBS10) 2.
3. Hardware Installation Note: The maximum amount of power available is 30 Watts per port and 120 Watts total. If a power overload has occurred, the Switch will prioritize the distribution of power by port (from lowest to highest). That is, port 1 will receive the highest priority and port 4 will receive the lowest priority. The ports with lower priority will have its PoE function disabled until more than 7.5 watts of power becomes available.
3. Rotate the TI-PG541i downward towards the rail to lock it into place. You will know it is secure when you hear the click. Mounting the unit Releasing the unit 4. To remove the unit, pull down to clear the bottom of the DIN-Rail and rotate away from the rail. Applying Power 1. Connect the power supply (sold separately) to the included terminal block (as shown below) and secure with the screws. Note: Polarities must match. 2. Attach the terminal block to the unit.
Optional: The switch chassis can also be connected to a known grounding point for additional safety and protection (grounding wire is not included) GND Safety Note ! Ÿ Turn off the power before connecting any module or wire. The correct power supply voltage (48 – 57 V DC) is listed on the product label. Check the voltage of your power source to make sure that you are using the correct part. Do NOT use voltage greater than 48 – 57 V DC, as specified on the product label.
4. Hardware Configuration 1 2. Assign a Static IP address to your computer's network adapter in the subnet of 192.168.10.x (e.g. 192.168.10.25) and a subnet mask of 255.255.255.0. 3. Open your web browser, type the IP address of the switch in the address bar, and then press Enter. The default IP address is 192.168.10.200 4. Enter the User name and Password, and then click Login. By default: User Name: admin Password: admin Note: User Name and Password are case sensitive.
5. Click Basic Settings and then click General Settings. Basic Settings General Settings 6. Configure the switch to match the requirements of your network. Then click Apply. Apply 7. Click Save. Save 8. Connect a network source and devices to the switch. Check the LEDs to confirm the connections are established. Your installation is completed.
5. Additional Information 1. Redundant power inputs V+ ALM - + PWR V- RPS + V- - 48-57VDC V+ DC-Jack Terminal Block Redundant Power Input: Choose either “DC-jack” or “Terminal Block (PWR)” as primary power and “Terminal Block (RPS)” for secondary power source, to be a redundant power Input. 1 NO 2.
3.
Manufacturer’s Name and Address TRENDnet, Inc. 20675 Manhattan Place Torrance, CA 90501 USA Product Information: Model Number: TI-PG541i 6-Port Hardened Industrial Gigabit PoE+ Layer 2 Managed DIN-Rail Switch Product Name: TRENDnet Trade Name: TRENDnet hereby declare that the product is in compliance with the essential requirements and other relevant provisions under our sole responsibility.
Limited Warranty TRENDnet warrants its products against defects in material and workmanship, under normal use and service. Specific warranty periods are listed on each of the respective product pages on the TRENDnet website. Garantie Limitée TRENDnet garantit ses produits contre les problèmes de matériel ou de fabrication, dans des conditions normales d'utilisation et de service. Les périodes de garanties précises sont mentionnées sur chacun des pages produits du site web de TRENDnet.
Safety notes Before using your TRENDnet device for the first time, it is essential to read and understand all safety and operating instructions. Keep instructions in a safe place for future reference. DANGER due to electricity Warning: Never open TRENDnet devices. Doing so poses the risk of electric shock! The device is voltage free only when unplugging from the mains power supply. No physical maintenance of TRENDnet devices is required.
Certifications This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received. Including interference that may cause undesired operation. Waste electrical an electronic products must not be disposed of with household waste. Please recycle where facilities exist. Check with your Local Authority or Retailer for recycling advice.
