User's Manual
Table Of Contents
- Product Overview
- Router Setup
- Basic Router Settings
- Wireless Networking and Security
- Advanced Router Settings
- Change your router login password
- Manually configure your Internet connection
- IPv6 Settings
- Clone a MAC address
- Change your router IP address
- Set up the DHCP server on your router
- Set up DHCP reservation
- Enable/disable UPnP on your router
- Enable/disable Application Layer Gateways (ALG)
- Allow/deny multicast streaming
- Identify your network on the Internet
- Set your router date and time
- Create schedules
- Access Control (IP Protocol Filter)
- Inbound Filter
- Open a device on your network to the Internet
- Virtual Server
- Allow remote access to your router management page
- Using External USB Storage
- Virtual Private Networking (VPN)
- Router Maintenance & Monitoring
- Reset your router to factory defaults
- Router Default Settings
- Backup and restore your router configuration settings
- Reboot your router
- Upgrade your router firmware
- Allow/deny ping requests to your router from the Internet
- How to capture network packets
- Diagnostic Tools
- Ping Watchdog
- Auto Reboot
- Wireless Client List
- Check the router system information
- View your router log
- Router Management Page Structure
- Technical Specifications
- Appendix
© Copyright 2017 TRENDnet. All Rights Reserved.
TRENDnet User’s Guide
TEW-827DRU
41
Block all services
1. Log into your router management page (see “
Access your router management page”
on page 10).
2. Click on Advanced and click on Security, then click on Access Control.
3. Next to Enable Access Control, click the Enable option.
4. Review the Add All Services Block Rule. Click Add to save the rule. Commit your
changes to the router by clicking on Apply/Discard Changes in the left-hand menu, and
click Apply & Reboot.
Rule Enable – Checking this option turns on the Protocol/IP Filter and
unchecking turns it off.
Rule Name – Enter a name for the Protocol/IP Filter.
Schedule (Optional) – The schedule function allows you to define a schedule
when the access control filter should be turned on. To define a new schedule,
click New Schedule and refer to page 39 “
Create Schedules”. After you have
created a new schedule, click the drop-down list and the new schedule will be
available for selection. Note: Before applying scheduling, please ensure your
Time settings are configured correct and you have defined a schedule. See page
38 to configure
Time Settings and see page 39 “ Create Schedules” to create a
schedule.
Client IP Address Range – Enter the IP address or IP address range to apply the
protocol/IP filter. (e.g. 192.168.10.20-192.168.10.20 or 192.168.10.20-
192.168.10.30).
Note: The filter will not be applied to IP addresses outside of the range specified.
Note: In the Block Rule List, you can edit a rule by clicking
under the Edit column
next to the rule you would like to edit. You can also delete a rule by clicking
under
the Delete column next to the rule you would like to delete.
Inbound Filter
Advanced > Security > Inbound Filter
Inbound Filters allows you to allow or deny a specific range of IP addresses. You can
create a predefined range of IP addresses to apply to a specific feature.
Note: You can apply a predefined inbound filter to the following features:
Virtual Server
Gaming
Remote Management
1. Log into your router management page (see “
Access your router management page”
on page 10).
2. Click on Access, and click on Inbound Filter.
3. Review the inbound filter settings. Click Add to save the Inbound Filter. Commit your
changes to the router by clicking on Apply/Discard Changes in the left-hand menu, and
click Apply & Reboot.
Filter Name – Enter a name for the IP address range.
Filter Action – Select Allow to allow the specified IP address range or Deny to
deny the specified IP address range.
IP Address - Enter the IP address (e.g. 192.168.1.20-192.168.1.30).
Note: In the Inbound Filter List, you can edit a rule by clicking under the Edit
column next to the rule you would like to edit. You can also delete a rule by clicking
under the Delete column next to the rule you would like to delete.