Table of Contents 1 English 1. Before You Start 2. Initial Controller Setup 3, Connect your wireless access points 4.
Access Point Compatibility Before you proceed, please ensure you are using one of the access point models in the list and the firmware version of your access point has been upgraded accordingly to the versions Inculcated In the list below. You can download the access point firmware from rennet.
2, Initial Controller Setup Nita: Slobs connecting the wireless controller 1o the network and connecting chert devices such as access ports, follow the spats to set up your controller IP address settings and administrator password first. s @ Power 0.co0T o a5 3. Assign a static IP address to your computer's network adapter in the subset of 192.168.10x (8.9192.168.10.25) and a subset mag of 255.255.255.0.
5. Enter the User name and Password, and then dick Login. By default: Please Login g Password: admin m 6.To change the controller administrator password, click Account Settings and click Edit.
. In the New Password and Confine Password fields, enter the new administrator password and click OK to save the new password settings. You will ba prompted Immediately afterwards to login o the controller management page with the new password.
9, Configures the wireless controller IP address settings to match the requirements of your network and click Apply. LAN Settings. Wkt i i o Famish — £ o Cimabue 10. Using an Ethernet cable, connect the non-Poe Gigabit Ethernet port 5 located on the back of the wireless controller to your network (e.g. router, switch, sch} TEW-WLC100P e Ellen Network 11.
3. Connect your wireless access points Important Note: Please make sure your access points have met the requirements In Section 1. 1. Using an Theme cable, connect each wireless access port to Poet pores 1-4 (green) located on the back of your wireless controller. Nita: If powering the access points using their power adapters, you can connect the access. points directly to your network without a power giver Theme (PoE) switch or Injector.
4. Initial Wireless Setup E 1. Using your computer and web browser, access the wireless controller management page using the newly assigned IP address settings (configured In Secretion 2) and login. Nita: If the IP address tastings were not changed In Section 2, the default IP address settings for the controller ls are 192.168.10.200 / 256.256.256.0. Please Login m 2. Click Monitor and click Devices. 3. The access points will be discovers automatically and appear In the Device List.
4, After the access points are discovered and appear In the Device List, under the Action column, click £77%3 on each abscess point to add them to the wireless controller. Iota: It may take up to 1 minute for each access port to be added to the wireless controller. 5. Once the access points have been added to the wireless controller, the Status will change from NEW to RUN. Wireless Groups/Profiles 7. In the list below, sick Greats ta create a new wireless profile.
8. In the Edit Wireless Group window, enter the wireless network nameless for the wireless network. (e.9. Trend net-WIFT) Mote: The SAID is the wireless network name used o broadcast and be discovered by your wireless client devices to connect to your wireless network.. Sid Trend net-WiFi 9. For Roaming options, select 802.11k and OKE wireless roaming protocols to ensure fast {transition wireless connectivity for client devices when reaming between multiple access points. Roaming F7802.11k [FOKKER 10.
Installation Tips and Troubleshooting Q1: How de | configure my computer's network adapter with a static IP address? Iota: Please note that although the following procedures are provided to follow for your operating system network adapter settings to be used as general guidelines, however, it Is strongly recommended that you consult your computer or operating system manufacturer directly for assistance on the proper procedure for configuring network settings.
02: 1 configured my computer's network adapter with a static IP address, how da | Configurations my computer's network adapter to default settings and obtain an IP address automatically using CPD? Note: Please note that although the following procedures are provided to follow for your operating system network adapter settings to be used as general guidelines, however, it Is strongly recommended that you consult your computer or operating system manufacturer directly for assistance on the proper procedure fo
03: 1 typed In my Interment Browser Address Bag, but an emir message says “The page cannot be displayed.” How can | access the wireless controller management page? 1. Double check all physical cable and port connections. 2. Marks sirs the POWER/SYSTEM LED on the wireless controller front panel Is on. 3. Make sure your computer's network adapter is configured with a static IP address. (Refer o @1 for Instructions on assigning a static IP address). 4.
MACROCOSM 1. Navigate to your Applications fonder and open Utilities. 2. Double-click on Terminal to launch the command prompt. 3. In the command prompt, type Configure intifada Queen or en> to display the wired or wireless IP address settings. Note: en@ Is typically the veered Ethernet and en Is typically the wireless Airport Interface. Graphical Method Win your keyboard, press Windows Logo + R keys simultaneously to bring up the Run dialog box. 2.
